I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
SDK: 4.1.0
Hi, I want to send change notification. so I writes below this.
Some buf_id has got failure in zb_zcl_ias_zone_set_status.
So I added loop which get...
Hi,
We are working on a board with nrf5340. We are running the nrf5340 in normal voltage mode. So, we have connected the VDD lines to 3.3V. Since we are using USB signals...
how can I put nrf52832 in the system on sleep mode on advertising timeout?
Currently, on timeout, the device is going in system off mode and restarting on interrupt.
Hello,
I noticed that you improved the hardware design in version 1.4. Is it still neccessary to use a bias tee for an external GPS? https://devzone.nordicsemi.com/f/nordic...
Hello, I am still learning about BLE devices and have a quick question regarding the Generic Access Profile. I understand that GAP defines 2 things:
The discoverability...
Per the notes on https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/Download#supl-c - "Highlight: Updated library made to work with the new modem library...
nRF52832 SDK 17.2
We are trying to get the packet loss/error information on a per channel basis. It is similar to what is being discussed in https://devzone.nordicsemi.com...
I am using NRF dongle in window PC and scanning tags with nRF connect->Bluetooth Low Energy . Is there any way to change the scanning parameters of nRF connect for windows...
Hi,
I have downloaded the nrf5 Sdk 17.02 from the website. And I have found the ble_gls example in ble peripheral example part.
Kit : nrf52832
1. Can you please explain...
Hi,
I am using SDK 17.0.2. I am using write and notification characteristics. There is a write and notification communication between iOS app and device. After successful...
I'm running into a problem where my softdevice is triggering the fault handler but only when I'm also using the USBD. The panic info is below, I've tried to double and triple...
I am working with signled door sesnor and it supports ZigBee 3.0 as it has an install code and mac address on the side of the sensor in the form of a QR code. When I run the...
We are using the latest pc-ble-driver with SoftDevice v6.1.1 and latest connectivity firmware on an nrf52832 (s132) which is connected via usb-uart.
We were previously using...
Hello!
I am flashing software over USB as I do not have a 10-pin JTAG cable yet. After I flashed a sample file on to the Thingy91s SIP it is no longer showing up in nRF...
