Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hi all,
trying to get CAN-bus support under Zephyr. Have a seed CAN bus shield link connected to PCA10040. The shield use SPI2 connected to MCP2515 CAN controller link ...
Hello
Is it possible to use the qspi of the nrf5340 for custom spi devices? I need the quad spi for the 96MHz speed which the normal spi does not have.
I know of the nrfx...
Hi there,
I am using the Nordic SDK 16.0.0 on an nRF52840 with FreeRTOS. I am quite familiar with using FreeRTOS, but hadn't needed to delete a task until recently. It seems...
Hi everyone,
How could I disable notifications from a characteristic when the peer is get disconnected from the the peripheral? My problem is that when notification are...
Hi,
I was investigating the registers of the nrf9160 using segger embedded studio and found POFCON, which is not mentioned in the documentation.
Can you provide...
I need to add some IPSO objects for our project. It is not quite obvious to me if I need to create modules similar to i e ipso_temp_sensor.c or if it would be enough to use...
Hello, guys!
We are desiging our custom board based on nRF9160 SiP. The board will be battery powered. Li-Ion rechargeable batteries will be used to supply the device. ...
Hi to all,
i am developing a device based NRF52840 soc, and i want to implement a device that need to store some public/private key in somewhere. i know that cryptocell...
Hello,
I am developing on the NCS 1.4.0 and on a NRF9160DK. I am working on the asset_tracker example and I noticed that the code sends an assisted gps request to NRF...
Hi,
I am using app_uart library with Tx and Rx FiFo. I want to check how much space is available in the Tx FiFo at any time, and similarly how much space is filled in the...
Now I am using Nrf52832,SDK15.0.0, S132,
When we developed the DFU OTA function APP, we encountered some abnormal situations: it could not get out in the bootloader mode...
HI,
I am trying to read the payload length of the data coming in a topic via MQTTSN over OpenThread. In the event handler, I am getting the event and trying to get the length...
Hello everyone
I am having a problem with the nRF Connect SDK 1.3.2 and the bluetooth peripheral UART sample on the nRF5340 PDK. The programm compiles and runs (the chip...
