Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello Sir or ma'am
I am trying to load CPP SDK on my nrf52840 DK, But whenever I compile my code it through the error like this," vector: No such file or directory". Now...
Hi, all.
I'm using nRF52832 Software Development Kit, PCA10040, S132.
Using the 'ble_app_uart_c' example, I am studying to connect with my beacons and read data.
I...
Hi,
When evaluated under the following conditions, there was Out of band spurious@325MHz~403MHz (See the following Results ).
Does nRF52832 has spurious(-50dBm~-60dBm...
Hello!
I'm doing the firmware that will be applied to the custom device. This device contains one button, which has two functions. (Function output according to button input...
Hello. I have one multirole device and one peripheral device. Both are nRF53832, SDK version is 15.3 and softdevice is s132 6.1.1. Multirole devices connect to phones as well...
I have two nRF52832 side by side scanning for advertisement with filter by name. Because I will have a number of peripherals advertising, so I want to have multiple centrals...
Hello together,
I want to create a program for the nRF52840 DK and later port it to the nRF52840 Dongle (both from Nordic).
The program should
1) over Serial (USB, that...
Hi there,
I have developed a small sensor device, which generates events when a reedcontact is triggered. When an event occurs a NB-iot message is sent.
However when I...
Hi All,
I'm a student starting a project on a low-power bluetooth accelerometer. I have selected the MC3672 accelerometer ( mcubemems.com/.../) , which will be soldered...
Hello
I am using the ble_thread_dyn_mtd_coap_cli_pca_10056_s140 example and I would like to send 100 bytes of data to display in the logs of the android application "nRF...
hi I am sending a sensor data with time stamp using bluetooth ,now i am sending every data seperately my question is can i store 100such data in structure and send that entire...
Hello,
I have NRF51822 and I need infinite connection. The chip is used as peripheral device. Tx power is set to -8dBm. What is the power consumption when It is connected...
I'm getting a softdevice assertion at PC=0x14CBC after calling fds_record_write(NULL,&record), the record contains the following information:
fds_record_t const record ...
Hi to community!
I have a trouble with nRF52840 when using TWIS. I initialize the peripheral by below code. If the device is reset using default pin 18 by the external...
