Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hi, Suddenly I can not connect to my nRF5280 PDK (PCA10056 0.11.0 2018.3)
1. I tried using JLinkExe and also SES, the same result, I got error "Can not connect to JLink...
Pins are denied to work as GPIO after the TWIM "Initialization -> Deinitialization" cycle.
After deinitialization, respectively, disable pins from the periphery, using the...
Hi all,
I am extending the BLE Multi-link example from SDK 15.2.0 in order to have some characteristics as BLE Mesh. I would like to use UUID filter to scan all peripherals...
I'm seeing similar problems to others in getting highly unreliable connections to the network. I *VERY* occasionally get LED3 and LED4 to blink simultaneously, but it's very...
Hello.
I take the flash_fds example from nRF5_SDK_15.2.0_9412b96, but I am not going to use the CLI (command line interface) because I take the FLASH written, reading capability...
Hi,
I am using nRF52832's ADC function to do my project, and I have an analog signal level problem.
I am try to connect MPX5100 sensor to nRF52832's ADC port, but the...
I am trying to use ARM GCC in macOSX and successfully generated .HEX file with the most simple project: the blinky project without softdevice. After setting up the project...
I am trying to use dsm_local_unicast_addresses_get() to store the address of each node, however it seems that when the board is restarted the value is lost, and node_address...
Hi,
I have troubles using nRF Mesh with my Vendor model.
I have made a Vendor Model that should allow me to send messages through Mesh. Once my boards are provisionned...
Hey everyone
This is sumanth, I am working low power node in mesh networking, I followed the procedure mentioned in below link for building and flashing
https://www.nordicsemi...
Hi I have a device which can get RSSI value from other devices.
But how do we get RSSI of my device itself.
i.e How to print RSSI of local device on the same device terminal...
Hello everyone,
Today I worked on custom bootloader and according to the article infocenter.nordicsemi.com/index.jsp I tried to load output hex file from IAR on board via...
I want to add a new ble service in hrs example(sdk15.3),I build and run the hrs example.and then I open the terminal emulator, but I can't find anything.I try to click the...
