Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I built the secure bootloader UART project without changing anything and I cannot program it using nRFgo Studio. It says:
This hex file has data in SoftDevice region. Try...
Hello,
I'm trying to use the Arduino BNO055 shield with PCA10040. This should be quite easy....but it doesn't work: I can't get any acknoledgement. Arduino use 5V pins,...
Hello,
I habe got a nRF52840-Development Kit. It is Herdware Revision 1.0.0.
While going through the Getting Started i find that the LEDs do not flash and that i have...
Just a heads up for anyone who bumps into this and is scratching their head. If you have ninja version 1.9.0 installed your build may hit an error with messages like this...
Hi everybody,
we have a remote control based on the nRF52832 and are experiencing a wierd issue with notifications.
We are using a custom 6 byte payload keymap characteristic...
Hi all, I use NRF52832.
I have a problem. I want when I connect to my chip and bond. After bond success, I insert new service. And when I disconnect from my chip, new service...
On page 69 of nRF52840 Product Specification 1.0 4413_417 v1.0 / 2018-03-16:
The table in section 5.3.6.8 shows that the WDT is NOT reset from a Wakeup from System OFF mode...
Hello,
We have an application based on ble_app_blinky that is actively scanning for advertised packets but does not attempt to connect. We have a second application based...
Hello,
i am using nrf52832. i am using 8 different pin as a 8-bit parallel port.
in my process i have to read each bit from each pin then converting those bit into byte...
I am using an nRF52840 DK. The software I have in it is emulating an NFC Type2 tag and is implementing a BLE peripheral.
When the device starts up everything works as expected...
Good day!
In SDK 12 I read values using this code:
and handle value in ble_evt_handler:
This works fine, but using SDK 15 this code crashes with fatal error...
This application uses a Rigado nRF52840 module to collect SPI data from 2 peripherals in slave mode. I have been unable to get the SPIS example running in the target board...
Hi,
This is a really weird problem.
======================
Setup of 52832 hardware:
- Custom board, using 32MHz XTAL and LF RC.
- SDK15.2, S132 610
- Segger RTT...
