Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi
Newbie in the nRF family of products so i might have missed the answers to my questions somewhere in the documentation and forum. if so i apologize.
I'm trying to get...
Hello ALL,
I have been using UART module and fstorage module in an application. I've been sending a bin file from PC to NRF52 using UART but when I tried to save it using...
Hi All,
I have some code that I'm porting from a Zilog platform over to the nRF52 platform. The code uses 1 timer and 1 uart. The goal of the code is to handle RS485 messages...
I am testing the IoT_lwip_MQTT_publisher_pca10056_s140 example project from SES on Windows.
I build and install the kernel with 6LoWPAN module on the Rpi3!
I can run from...
Hello，I'm from China。
At present, there is a need to broadcast beacon data in nrf51822 (SDK_12.3.0_d7731ad is used as the protocol stack version, and the...
Hi
I want to generate two PWM signals that are phase shifted with 90 degree, with similar duty cycle. I have the following pwm configuration, but I don't know how to proceed...
I am operating as a Central. How do I register and enable a discovered characteristic's indication?
I do the following and the subscribe passes but then the kernel crashes...
I'm planning to buy a nRF51822 based module for my BLE project & I wanted to know whether any of the nRF51822 based modules come with OTA ready bootloader out of the box....
Hi,
I'm trying to save sensor data to sd card on low power mode. When i connect to bluetooth mobile app can pull all data from sd card.
How can make this architecture...
Hi,
I'm using Nordic BLE Sniffer. When I look into the captured data I see a lot of malformed packet (CRC error). It try to decode any received data even if there is CRC...
I was digging around a bit in my code to get a better grip on logging. In sdk_config.h, I have the following relevant settings:
My modules all implement their own logging...
I am going to implement DFU over BLE in my nRF52832 project. Since the size of my application + softdevice larger than half my memory size I wonder how the update is performed...
We're looking to use the nRF91 to measure the LiPo battery voltage to determine battery health. We would want to know what the accuracy and range of %XVBAT is. Looking at...
I am trying to create CTS server using nRF 52840 dongle and nRF Connect PC app (v2.6.1). Currently I can manually provide current time and local time information to the app...
