We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
i am playing around with configuration of Softdevice (S112 ) + bootloader + application.
Bootloader is custom, really simple. Flashing block of data received via uart...
Hello, I wanted to understand what is the default storage place in the internal flash memory region of persistent info for OpenThread. In the previous SDK (Thread and Zigbee...
Hello DevZone,
I have 2 Thingy91X (not Thingy91), with nRF9161 and nPM1300 inside. These two devices run out of battery for several hours.
The problem is that I can't...
Hi，I have some problems using the NFC routines in the SDK.
The hardware used is nRF5340 DK.
Software is nRF Connect SDK v2.6.99-cs1.
The downloaded and run routines...
Hi,
We have designed a custom board for npm1300 and nrf52832(MS50SFA2 module). We would like to drive the VCC of the BLE module using buck2 but we are only getting 1.8V...
Hi,
I have to use Nordic SDK and VS Code Dev Kit on my company enterprise PC but I cannot fetch the toolchain or install SDKs via VSCode or nRF Connect for Desktop
...
Hi everyone,
I'm the author of the following question and a lot of context information about the state of our custom application can be gathered from there: registration...
Hi,
In my app I have been using the following to register my state change callback. This works. Only issue is it seem to only pass ot_instance, I cant pass a user data to...
Hello All,
I am attempting to use the scanning module to scan with a multiple filters. UUID and NAME filters to be exact.
I have done some testing with the code below...
We are seeing different behavior/performance on our system depending on whether we reset the system using JTAG (JLinkRTT Viewer) or we power cycle the system.
Our project...
Hi,
we would like to extend the measurement range of the PPK2 beyond 0.6 A in source meter mode, e.g. to measure the power usage of a Raspberry Pi. We know that this might...
I need a checksum to verify integrity of some data blocsk. As I saw, that the nrf5340 hardware has some builtin support for SHA-256, I though: cool, let's use SHA-256
Now...
Hi,
I build a custom board (nRF52840) but I'm not able to flash it using nRF5340DK with J-Flash via SWD interface.
1. The first thing I did was to do a full chip erase...
Hi,
Is it possible to communicate with the nrf52840 dongle from an android application via USB port ?
That is, nrf52840 dongle will be inserted to the android phone's...
