We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
HI
An example of zigbee multi-sensor is to use log enable info zigbee.report to enable log display. Is there any more information that can be turned on and displayed in...
Hey there! I'm very new to BLE, so I wanted to reach out in this forum to confirm hardware capabilities before I purchase any devices. I'm currently looking at the nRF52840...
hi team,
i am using nrf52840 controller,in my project along with with nrf_sdk.
i wrote a led blicking code using ble protocal on segger IDE 5.40 and i want to see data...
Hi, I'm using nRF52840 in my project. I successfully integrated the BLE DFU service and its characteristics in my firmware, Now I can update the firmware through the nrf-connect...
Hi, we are doing mass production using PLT. And we have found that like 10% of the sensors are stuck in certain stage as seen in following power cycle images.
The program...
Hi,
In the product specification document of nRF52840 it says that in order to read the counter register's value I need to set the capture task NRF_TIMER1->TASKS_CAPTURE...
Hello,
I would like to use the UICR customer registers to store our devices serial numbers.
Can you please point me to some example code for nRF52833 SoC.
I am using...
Hallo Team,
I would like to operate nrf5340 BLE module (BC40C from Fanstel) in "Normal Voltage Mode". Please find the screenshot of the module below. I hope its clear...
Hi,
Just wondering if it's possible, or there is a reliable way to dynamically change the sampling period of the CAF sensor manager module . Specifically the values defined...
Hi everyone!
I am using ESB with the nRF5340dk without ACK, but from time to time need to send a packet with an ACK request in order to send some commands from the receiver...
Hi,
After successful building of pca10040_s132_ble_debug example with changes to project :
- excluding SEGGER_RTT_Syscalls_SES.c from build
- from flash_placement.xml...
Hi,
We are hoping to send our samples for CE certification. We use nrf52805 IC in our design. We do not use any precertified modules.
Looking at the Direct Test Mode folder...
Hi!
We're working on a development project using nRF52832. Our original prototyping PCBs used the nRF52832-QFAA. On these boards, the nRF worked without issues, and we could...
Hi,
I have builded a circuit with a nRF52DK and a mpu9250 IMU. If I power the Sensor with VDD the Zephyr driver and all of the Software performs well and the values from...
