Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
I am having a lot of trouble adding a driver to my application. I have followed the tutorial here: https://www.zephyrproject.org/how-to-build-drivers-for-zephyr-rtos...
Hi,
For my app (using zephyr and nrf52840) I want to use hardware Timer like that, is there any manual or example how to do that?
Need able to set period of timer from...
Hi!
We're working on an AoA application using a custom nRF5340 board and antenna array. Just trying to fully understand the interpretation of IQ data, there are a couple...
I can see that there are others that have had problems with finding SIMPLE information from this site.... I would like to get off on a better footing.
Here is the issue...
I'm considering transitioning a product codebase to the nRF family (nRF52 or nRF53).
It's Arduino code, with lots of C++ code.
As in the cpp_synchonization example provided...
Hello,
I'm having an error with the 832, specifically I'm just trying to port code over from an 833 project. I can compile no problem, but when I go to write I get
ERROR...
Hi there,
I've been working on creating a nice wrapper around the nrf modem library in Rust. Currently can be found here: https://github.com/diondokter/nrf-modem
When...
I was testing out the custom application from android studio, and have discovered that, for example, when using the rscs example my application does not see the device and...
Hi Nordic. This is a general question and could as easily have been posted to stack overflow but I have found the members and staff of this community so helpful and adept...
HI,
I am working on a application which has an requirement, that I need to read the current value if it is above threshold value then I need to turnoff the control. Here...
The executed command at connectedhomeip/examples/lighting-app/nrfconnect: west build -p -b nrf52840dongle_nrf52840
The messages i encountered:
...
/ncs/zephyr/include...
good day,
is there a way to set a gpio when in dfu mode? wanted to make GPIO 19 of nRF52832 HIGH during DFU mode because we assigned it as an enable pin.
in DFU mode,...
Hello,
I have my own custom board with nRF52832 and a NB-iot module SIM7080G that interfaces via UART.
I can easily program the device through SWD using J-Link. I am even...
Hello,
I am using flash_write_protection_set function with few low level function call for accessing extremal flash with nRF9160. And because of that I am facing one warning...
Hi,
I am programming the nRF52833 and using NCS v2.00. I have recently programmed the Peripheral Coded PHY to the board. I am using a Google Pixel 3 with nRF Connect as...
