I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
I've read many similar issues that were raised regarding high SPI power consumption, looked at various examples, but can't seem to find any issue that is close to what i'm...
Hello.
When going to sleep with the BLE connection established, the WDT counter will be added. (WDT behaviour: NRF_WDT_BEHAVIOUR_PAUSE_SLEEP_HALT) At this time, my app cannot...
In the usbd_ble_uart example (SDK 17.0.2), I'd like to use the buttons handler module (the same one from the BLE Blinky example), instead of the BSP BLE button events. In...
Hi!
In our development we are using nrf52833 and for the first development phase we used the SDK 17.0.0. In that case I used the usbd_ble_uart example with s113 and it works...
Hi,
I am Using nrf52832DK and SHT25 breakout board. I can't able to read a device address using "TWI Scanner". But, I can able to scan the sht25 device address by Arduino...
Hello,
I am trying to clear reset reason when it wake-up by GPIO.
In line 163, I set RESETREAS to 0
In line 164, RESETREAS is read again.
I expect 0. But It still...
Hello,
I use nRF52832's COMP (comparator) to sample a pulse signal's voltage level.
I found when the pusle width is below like about 60us, the COMP can't get correct...
Hello,
we need to feed mono audio data into the nRF52 and we are now evaluating the possibility to use PDM. The nRF52 seems to have a useful PDM interface , and even though...
Hi,
I would like our nrf52840 to use coded phy 8x to get longer range.
The counter part are Android smartphones, old ones with BLE 4 support only, new ones having coded...
Hello,
I have a custom PCB which uses the NRF52832 chip and i wanted to program it using the NRF 52 DK using P19. I have the following connector and pin out on my custom...
Hello everybody !
I am working on a project and I need to create a server node which also works with the nRF SDK.
As I have seen, it exits coexistance examples where both...
Hi there,
I am trying to use the ISP from the 6700. I need to power my development board. I was wondering if there is a pin output on the nRF6700 motherboard? There is...
Hi,
The end goal is to run this project on a Thingy91, but I am currently building/testing on the nrf9160dk.
I am looking to capture ANT+ from a bike power meter on the...
Hello Nordic,
I'm evaluating the --external-app option of nrfutil and I noticed something odd.
First, I create an example hex file with 8kb of random data and then run...
