I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
To automate some testing procedures, I was wondering if it is possible to use the firmware, which runs on an nRF5x to connect to nRF Connect for Desktop, but with a...
Hello all,
I'm fairly new to BLE and Linux BlueZ.
I'm trying to interface a Mikrobus BLE module based on nrf52840dk to our Yocto based Linux SBC (Rugged board i.MX6-UL...
Hi Nordic Team,
I am new to embedded developing and I am learning about logging data while working on nRF connect sdk" .
kit:nrf5340
SDK: nRF connect SDK v1.5.0...
I'm finding that the MCUBoot stays stuck in bootloader mode sometimes when using a CONFIG_BOOT_SERIAL_DETECT_PORT.
I've narrowed it down to setting up the GPIO as input...
Dear !!
Good day!!
I want to change the device name using command from mobile along wither after setting the device name i want update the Password, so can you share...
So,
I've got a working framework for my project - a battery powered appliance that will occasionally trigger one of two solenoids, timestamping the operation and subsequently...
I've got an issue where calling a function is overwriting a variable in the calling function. See attached screenshots. In the first, byte is 0x1b. After stepping into the...
Hi,
I am trying to send data over UART to a dispensing unit using Space Parity but am unable to do so since NRF51 only supports Even Parity. Is there any work around through...
Hello, I am trying to implement 1-1 connection between a central and a peripheral, with these (classic) requirements : - when starting central, scan for any peripheral with...
Hi,
I am having some trouble getting optimal power consumption while using the SAADC.
I've tried running the example given here 2766.nRF5_SDK17.0.2_ble_app_beacon_lp_saadc...
Hi,
We are trying to investigate the interval noises of our custom developed sensor board with a digital accelerometer (With SPI interface).
After checking the software...
Hello NRF ,
I have used NRF52832 with BLE advertise and peripherals connected on two different I2Cs ( temp sensor and gyro sensor ), One SPI( LCD Display ) , three GPIO...
I'm working with nRF52840 dongle, i installed nRF Connect for Desktop on windows but the led didn't start pulsing red. Has anyone else had an issue like this?
I am using SDK 16.0.0. I want to switch from a NON-CONNECTABLE, NON-SCANNABLE advertisement to a CONNECTABLE, SCANNABLE advertisement. I launch the first advertisement and...
