Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi,
Our entire board is running around a nRF52832. Recently it has been difficult to find some of these SOC. Is it safe to replace it with the nRF52811 without changing...
Hi,
I am trying to compile ble_advertising.c file for a specific application based on nrf52840 and I am getting the following error:
nRF5_SDK_15.3.0_59ac345/components...
I am working with an nRF52840 on a custom board. Our device has a number of sensor attached in various ways including spim, twim, uart. I've used the ble_app_blinky as a starting...
Hi Dev Team,
I am enhancing my Thingy91 application using the mqtt_simple sample and NCS v1.5.0. I am basically connecting to the MQTT broker, sending data and then disconnecting...
I am using nrf52840 as PTX and nrf24l01+ as PRX. The application I am working on requires me to send 30 bytes from PTX to PRX at a 2 kHz packet rate. If both devices are near...
I am trying to make ble communication work with I2C but i cant make it work i dont understand what is the issue the code is being build but it does not advertise can someone...
I'm building a firmware for nRF52 which is using app timer v2 with RTC1. After a while, app_timer starts running many times faster than normal, and I'm not sure why. Nothing...
I use pc-ble-driver to control nRF52840 dongle. I want to speed up scanning of advertising time.
So I change SCAN_INTERVAL and SCAN_WINDOW.
How can I modify the parameters...
The enocean_switch example has MESH-config example, to store data in FLASH, within the mesh rules.
I use it in my app, IT WORKS, but the biggest data array what I can store...
hello folk,
I am working on nrf52840, I want it to assign Static UID of any kind that even won't change after the device gets reset.
I have already gone through "FICR...
Hi,
I am looking at using the nrf5340/nrf9160 in a device. In this device, I need to have high endurance storage of some data that must be kept secret, integrity checked...
Hi,
My project involves an nRF52840 DK connected to an accelerometer on a breadboard, connecting to my Mac via USB-micro.
I'm editing the twi_scanner SES project so...
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
I took ble_app_uart example, and then modified it to run I2C, SPI. everything is working fine
problem I...
I have a question about how to perform DFU over Mesh.
I'm using nRF52840 device.
Following the steps at the URL below (Configuring and performing DFU over Mesh), I'm trying...
