I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
(Windows10, Android Studio 4.0.1, SDK 15.2.0, nRF52832 dev board, App run on Galaxy S10, latest Android version).
Hi, I'm looking to use the Toolbox to create a template...
Hello,
I am having a few issues with getting the SD card FATFS example code to share the same bus as another slave I transfer data to.
I have a few questions:
1) Since...
Hello,
I'm flashing custom code onto a nRF52840 based PCB.
I'm using SDK v14.2, SES 4.52.
The board was running fine for a couple of days.
Suddenly when I reflashed...
Hi,
I started coding form ble_app_uart, and whenever I set a breakpoint and it's caught, then I press Resume (eclipse), the code falls on NRF_BREAKPOINT_COND in app_error_fault_handler...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
When SPI sending...
1.Development board used is nrf9160DK，sim car is nb-lot,set's network mode is nb mode，Turn off all peripherals
2.set eDRX mode,eDRX is 655.36s,pwt is 2.56s ,After the device...
I am using the GPIOTE driver to attach interrupts to a pin in a very timing critical environment (using sensors like this ).
To me, it seems like there is quite the significant...
In the v16.0.0 SDK the settings struct size is 904 bytes, but in the nrfutil it's 803 (screenshots attached). I figured the settings in python don't include peer_data(64bytes...
I was in the process of integrating a NAND flash to my project. - MX35LFxGE4AB
Initially, I thought it would be good idea to use QSPI, but it seems to only support NOR flash...
Hi
Im struggling to use the ble_app_template_cpp within SDKv16. I am using the nrf52840 DK (PCA10056) and want to us the S140 SoftDevice. The example isn't built for either...
Hello everyone:
The problem is still not resolved
Test broad is PCA10056
Test code was modified by \SDK17.0\examples\peripheral\usbd_msc\pca10056\blank\ses
Try to...
I am using a thingy52 device and in that, added code of advertising and scanning from the sdk 16. Advertising is run successfully. But getting packet loss issue. So, I am...
Hi
Im developing an application that will wake up on RTC every 15 minutes. My issue is that when using idle_state_handle, which in turn calls sd_ble_app_wait, the RTC...
Hi,
Trying to figure out the current requirement on GPIO input, can you point me in the correct direction in how to figure out how much input current the GPIO on nrf9160...
Hi,
we are planning to add a 256 MByte NAND flash to our sensor project. I saw the example for NOR flash on the PCA10056 which is working fine. But due to costs we want...
