We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I wanted to confirm my understanding of the Replay protection cache. In the code, the limit is set to REPLAY_CACHE_ENTRIES and there is a note that says:
@note...
Hi to all.
I am new to this forum and to the Nordic range of products.
My experience over the last few months have been with arduino and Feasycom bluetooth modules. I...
Hi,
Since I updated nRF connect from 3.6.0 to 3.6.1, I get this error when I try to connect to a device :
"Error when getting device info: Error: Error: Error occured...
Hi,
I'm trying to devise the hardware platform for a Home Monitoring medical device. In the first place I planned to use the NORDIC nRF5340. With its large memory it would...
Hi.
We have a debug board for the NRF52832. The breadboard on this board is working fine. But if NRF52832 is used outside the debug board, then for some reason, some phones...
I want to set the Device's current date and time as I have to check time after certain interval. I don't want to use RTC where we have to look for ticks.
My questions...
Hello,
Could you please let me know if any of your devices would be suitable for our specific configuration?
We have a WMware server running many VMs. We would like to...
hello i am using nrf52832 and mpu6050 accelerometer with sdk 16 while programing i used 27 as scl and 26 as sda which is default in nrf52832 and i had no issues while reading...
Hi,
I am trying to test the light_lightness example present in ' nrf5_SDK_for_Mesh_v5.0.0_src' , on nRF52 Development kit(pca10040). And i am provisioning the device using...
I have a production device which I have soldered an SWD connection from a Keil project via the nrf51822 DK (port 20). I can flash code to this production device, but I cannot...
I'm using a SPI with a circular buffer so i need to have an interrupt with low latency that reset the RXD.PTR when the buffer is full.
The SPI is used for communicating...
Since Zephyr’s official BLE sample code, his BLE central only supports one central to one peripheral So I refer to the BLE central multulink officially provided by nordic...
HI ,
My name is MOHAMED ALI SAIDANE from Tunisia , i've been working on my project of the last year eduction , i'm interresting about the concept of the module NRF24l01...
We are using a custom ARM board which runs Linux and has a UART interface to a nRF9160.
I'm not how to phrase this exactly so I will just describe what I would like to do...
