Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
If i buy a raw nRF52832 chip and design the circuit by myself, how can i pre-programm the serial bootloader in it? So i could use the FTDI Basic (or an FTDI Basic -like device...
Hi,
Is there any way to change the advertisement name before switching to DFU mode?
I have a custom app that reboots into DFU mode (via NRF_POWER -> GPREGRET ). I want...
Hi,
I've to design an alimentation with capacitors to keep energy and filter current peak. To do that I need to know timing for NFC peak current. Do someone have information...
Hello,
I have a running system constituted of a central and 15 peripherals using nRF52840 devices. The central is set to scan the peripherals for 5 seconds then stop and...
Hello,
I'm implementing a beacon scanner with nRF52 using nrf_ble_scan.c. After the scan has been configured with no filters, no advertisement reports are returned to the...
Hi,
The definition of the COEX1 pin looks to be really interesting for applications that need a reliable time reference. A 1PPS GPS output is very useful; absolute accuracy...
Hi
Our nRF9160DK card seems to have stopped working. We attached a sensor to the card (We might have connected the reset pin on the P7 strip) and now I can't start any program...
I was trying to make sense of the serial support in mcuboot, but it uses a protocol and format I don't recognize. I expect they're generated by the Apache Newt tools, since...
I am designing a board based on the nRF52832 and wanted to examine the reference design files 'nRF52832-QFAx Reference Layout_v11.'.
However, The the downloadable files...
Hello!
I am using a nRF52832 with the S132 v4.0.3 softdevice. But I get an error from the softdevice via softdevice_fault_handler.
It gives me id 1(which suggest a NRF_FAULT_ID_SD_ASSERT...
Hi,
I'm using SDK 15.2. The bluetooth disconnects when I enable notifications on nrfConnect. This happens only if I increase the number of bytes to be sent. I'm writing...
hii,
i am currently using light switch example proxy server and proxy clients.
here i am using 3 boards ,2 board(node B &C) are programmed with 4 generic onoff servers...
Hi,
We have a bluetooth product which uses Nrf52840 as the MCU. It composes of a peripheral and a central device of which connect with each other via bluetooth and they...
I have a question about "SEGGER Embedded Studio for ARM V4.12".
I specify a hex file in "Project Options"-> "Debug"-> "Loader"-> "Additional Load File [1]". With this setting...
I have a question about TX Power.
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
The device operates as a “Peripheral”. Is there a way to know...
