Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi, what is the correct way to erase all the connection params of a zigbee router device (not coordinator), and restart to search for a network automatically in production...
Hello,
I am using SDK 15.2.0 ,nrf52840. In my application we are using bluetooth and USB. The application works good. The device advertise and can get into the application...
Hello,
I have SDK v15 and there is not much information in infocenter also about these two functions related to my doubt.
( NRF_PWR_MGMT_SHUTDOWN_GOTO_SYSOFF & nrf_pwr_mgmt_run...
Hello, I'm starting evaluation of the Mesh Light Switch Demo both on DK PCA10056 and on Dongles PCA10059. I 'm using SEGGER IDE and made sure to properly set target in Preprocessor...
Hi , i tried to modify the template example from the sdk 15.3 but im getting an compilation error from " nrf_log_backend_rtt.c"
SEGGER_RTT_Conf.h: No such file or directory...
Trying to up load mqtt_simple sample, however getting bus fault on terminal. have browsed after the same issue here, but don't work after doing git pull ect...
here's...
How to correctly reinitialize the BLE stack when using FreeRTOS?
I can not find in the libraries where the task for the work of the stack under FreeRTOS is created.
Stopping...
We have a connection between our nRF52832 (server) and a tablet (client). We're trying to transmit some data at a rather high throughput. The connection parameters are as...
Hi everyone,
I have a problem with my custom nRF52832 hardware. I soldered my prototype hardware and then I checked if it is correct by checking debugger SW device settings...
Hello,
I'm trying to get as much throughput as possible using the Coded PHY. I noticed that apparently the Data Length Extension feature is not supported together with the...
Sometimes, i found that my firmware still at the old version after update complete, there is no any error.It same happen on use Android-nRF-Toolbox to update firmware.
code...
Hi, I am interfacing external memory chip that is based on SPI protocol with nrf51822. I have to read more than 255 byte via spi in single buffer with 4 byte of command. Even...
Hello,
I am using a custom board with nrf52840 using SDK 15.3 and ICM 20948. I see a lot of twi drivers and its confusing which one to use. I want to read the ICM 20948...
I am using a Windows machine and would like to compile a sample nrf5* project (preferrably nrf52) by using the command line only - no GUI.
Can you please tell me how I might...
