I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hey, i’m working on implementing the adafruit_tag_reader example from the SDK v13.0.0 on my Thingy 52. I have copied almost all the code from the adafruit_tag_reader example...
I modified the FW "ble_app_uart" using the example "Nordic-SDK\nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\en_app_uart\". I added the pairing function and "delete_bonds...
I want to connect 2 SPI slave with on instance. Issue is to mange chip select pin. I went through few post, people suggested to check SPI manger library. I am not able to...
Hello
We tested our product integrating the nRF52840 vers. C in DTM with the Anritsu MT8852B.
The RX tests (PER and sensitivity) pass but all TX tests (Output power, modulation...
Hello,
In my application I'm putting the NRF52832 device to the system off by calling the sd_power_system_off() function.
When it occurs at the start of the program -...
Hi are the example applications for use with the mesh provisioning app available for the nrf52840 as well as the nrf52832 devkits, or just for the 52832?
Best Regards, ...
Hi,
I want to add my own data into beacon advertisement packet. for example I want to add my data as "ABC0001", and it should be available in advertisement packet. How...
Hi all,
I am using the Power Profiler (v2.0.0) in nRF Connect (v2.5.0) to debug and profile some nRF52832 applications, and I cannot seem to find any button that allows...
(開発環境 ) OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit...
Hello,
I am using SDK 15.2 with softdevice 140 on nrf52840 board. I have been trying to get the development board to pair with a peripheral sensor with UUID "E7D4AA0F-5ACB...
I would like to know how to compute or optimize the maximum number of BLE device (in advertisement mode) that can be detected by a Scanner (Smartphone app).
I can not find...
Hello
Is there any example code in the Zephyr for operating as the Mesh provisioner/controller using the serial mesh interface on the nRF52840.
I am working on using the...
I'm having a peculiar problem with my device in a memory heavy application, two of my libraries use statically allocated memory and one uses what i allocate with mem_manager...
Hello.
I'm working for a Zigbee networking project.I chose nRF52840 as the coordinator.The coordinator acts as a gateway to communicate with Zigbee 3.0 devices on the market...
