Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
Since the last update of the 'Getting Started Assistant' (0.9.0) from 'nRF Connect' 2.6.2 on Windows, I can´t set up or compile any sample of the SDK for the evaluation...
So I've been having a problem the last few days - using the NRF52832 we have an SPI chip connected his chip requires a clock signal (1MHz) that is being generated by the NRF...
We have written code based on SDK V12.2 and found it doesn't support power saving mode. Given that it's very complicated to transplant to higher version, how can we fix the...
Hi,
I want to interface two QENC with nrf52840, I saw QDEC example and it works as expected.
The problem I am facing is that QENC has four pins of which two are for power...
Hello,
I am having strange issue. I'm getting some data from custom service and characteristic. I can see the data being received is correct. However, if I try to pass the...
Is there a set date for the release of a tracker SW with working GPS? And secondly, will there be a step by step instruction how to upgrade the software on the dev. board...
Hello,
I'm an Embedded system student and I would like to make an extension for ZigBee for which I need to make changes to the underlying ZBoss stack.
Is it possible for...
Hi!
Most of the project's application code is written in C++.
SDK headers are guarded with the extern "C" therefore when including no problems arise with linkage.
The...
Hello,everyone
nrf52840,use sdk15.3.0, and I just want to run the example uart,but there is an error which is :ble_link_ctx_manager.h:no such file or directory. and then...
hello ,everyone,
I want to add the dfu service to the hrs example, but after I follow the step by step guide operation, I import the (settings+softdevice+bootloader+app...
I've tried to use Nordic Infocenter ( infocenter.nordicsemi.com/index.jsp) and it doesn't show documentation pages. It shows blank pages instead (see attached screenshot)...
Hi,
I'm using S132 SD 6.1.0. I'm transferring some advertising data to the SoftDevice and it returns INVALD_PARAMETER. How can I find out, where the problem of the SoftDevice...
Hi,
I got an issue with a battery powered sensor with generic OOB NFC pairing. The NFC is used to pair the sensor with a gateway, but if the device is not connected it must...
I just got the nRF9160DK. Followed instructions in video.
1. SIM card activated
2. Input sequence (push buttons and switches)
Expected LTE device added in nrfcloud ...
