I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello,
I have several questions regarding BLE beaconing and scanning that I feel are pretty basic but I can't seem to find the answer. I have a nRF52840 Dongle that uses...
Hello,
Thank you for considering my inquiry! I am looking for an example project with the firmware to run a gateway through the PC, nRFconnect software, and a nRF52840...
Hi,
I'm developing an application with the following hardware and software design components:
- nrf52840 DK with attached sensor
- nrf52840 USB dongle attached to debian...
Hi, I have some issues with my eclipse setup, I have installed all packages and followed the tutorial ( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development...
Hello,
I am working on bootloader on nRF24LE1, for which a protected region should be configured. Therefore, I need to change NUPP in infoPage.
So my question is, is there...
Hi.
I watched the examples and docs with the on-off model. I tried to run these examples and configure. I don't understand when I need to use a server model when client...
I am seeing some behavior in BLE advertisement mode , that I would like to get feedback from expert in this forum. I am using modified Keyboard HID example, using nrf51 BLE...
Hi,
I'm using nrf52DK and 12.3V SDK .
in keil i can able to go to the debug session but when i press run button it is not working.
what could be issue ???
I have enabled RX address 0 only, (value of RXADDRESSES field is 0x01)
But still I got a received package interupt where RXMATCH has a value of 0x07, indicating that I...
Tx Radiated spurious emissions (1-18GHz): should be able to force the radio into a continuous transmit mode on a specific channel. The device should be transmitting with as...
Hello,
the BT specification states the following:
Is this particular requirement to be taken care by Nordic's customer using the BTIC? i.e. LE PHY qualification test...
Hi,
I want to use bsp_event_handler in SDK v11.0.0 . But the code is not getting compiled.
On building, it throws an error "error:#20: identifier "BSP_BUTTON_ACTION_RELEASE...
Hi,
I'm using NRF_LOG to print information via RTT backend (RTT viewer v6.20) and it has been working so far. After adding a single call to a function that reads 128 bytes...
I use one motor to drive one object move back and forth in a straight line, with two hall ic(XC3202) at the boundary points at both ends. The motor turn when the object reaches...
I'm using a central (Adafruit Bluefruit Feather nrf52) and peripheral (Adafruit Bluefruit 32u4) device for BLE communication. Peripheral is acting as remote, to turn on relays...
