Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
Currently I am sounding a simple beep on and off sound with a Piezo Buzzer on the nRF52832 and using the power profiler, it is consuming approx 713.323 μA, I was wondering...
Hello!
I have a question about the slave latency: I know how it should work, I would like to know if it is normal that there are current peaks in the supply current when...
Hi,
Does anyone have a hex code that can be added to the app hex in order to get rbp for NRF52832? Or a code that can be used from Arduino IDE?
I know that it can be...
Following error throwing while using nrf tools
nrfjprog verion 9.3.1 -------------------------------------------------------------------------------- FUNCTION: open_dll...
Can someone explain the indepth working of nrf dfu bootloader example with respect to the init packet.
How is it decoded and the information gets stored in the structure...
Hello,
I'm getting started using the nRF Sniffer with PCA10040 and Wireshark on MacOS. I followed the instructions in the User Guide and was finally able to set it up by...
Hi
This is just a head's up. In function nrf_esb_pop_tx(void) you have the following code ...
Instead it should be the following...
Otherwise the bug is such that...
The Introduction page is inconsistent:
infocenter.nordicsemi.com/index.jsp
first it says
[quote]]The mesh stack is also compatible with the nRF52810 platform, but not...
Hi all,
As I've been researching, the mesh sdk is not supported on the nRF52810 SoC, although being compatible. Is there any development or plan in changing this? I'm planning...
Hi,
Is there any way to add conditional compilation in linker file?
I have two versions of a code, one with DFU and one without, i want to combine the versions. is there...
Hi everyone,
I used SPI interface to access a external flash with page size 256 bytes.
I found I can't access full page, because the maximum of one SPI transaction is...
hello all ,
controller nrf51822
i am trying to development for EPD 7.5 spi interfacing through external flash image send so how to set spi latch reset turn on parameter...
Hi, there
I try to use the nrf_atfifo in my program, but I found the atfifo cause hard fault in my program,below is how I use the at_fifo in my program.
and I also found...
Hello, I have a problem with my nrf52832 customised board
It has loaded the ble_app_uart example of the 15.2_SDK and It have the correct pinout from my board, These are...
