Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi
I'm little bit confused about how FDS library allocate the virtual flash pages (according to the number and size in sdk_config.h).
I decrease the number of virtual...
Hi
I'm trying the remote client-server example. When I flash the code onto the NRF52832, all the 4 lights are lit. Here's the log i get:
0> 1) Provision first available...
Hi,
I was actually trying out Nordic mesh topology and wanted to tryout the example programs.
SDK: nRF5_SDK_15.0.0_a53641a
mesh: nrf5_SDK_for_Mesh_v2.2.0_src
IDE:...
Hi Everyone
I am using
SDK 15.0
Segger Embedded Studio
nrf52840 on a custom PCB.
Softdevice s140.
FreeRTOS.
My requirement is , on the press of a button , the...
In the news today (26 Oct 2018):
http://www.eenewsembedded.com/news/embedded-studio-410-arm?news_id=111432
Will this work with current Nordic SDKs, or should we wait...
I am using FreeRTOS (sdk 15.2) configured to use RTC for the tick source and systick timer for the system. I am trying to put the device in a low power mode. I have tried...
Hi,
I use Iphone to scan for arround ble package.
The beacon is configured broadcasting every 200ms (I think all 3 channels 37, 38, 39 is default to broadcast signal in...
Hello,
I have a secure bootloader and an application on nRF52840 with SD 15.2.
I try to add watchdog support in application based on watchdog exemple but if i remove feed...
Hi,
i'm actually working for interface the nRF52 with the STM32. Actually i completed the part where the STM32 send some data and the nRF52 recive it.
Now i need to do...
Hello,
I am a beginner with Nordic semiconductor. I downloaded SDK v15.0.0 and used some of the examples and it worked perfectly for me.
My project uses different modules...
Wiring diagram
Testing process，The product will automatically disconnect. But it can connect again.
After setting the voltage to 1.8V in the voltage Reguator,...
This time I am trying to run Wireless UART Example but it seems that it does not work.
After I flashed dev board no LED were turned ON or flashing but web site says:
LED...
Hi!
Is there an example to extend the Bluetooth MTU size to more than 20 bytes together with SDK 15.2?
I found only examples with older versions.
Thank you in advance...
Hello
I'm wondering if it is possible to upgrade over-the-air from SDK11 to SDK15.
I know already that using the example bootloader from SDK11 will not work because the...
