I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hello !
You have DTM test in nRF5_SDK_17.1.0 and in nRF Connect SDK.
I have used SDK test some years ago and it looks more simple if we compare it with new environment...
Hello,
I am working with the nRF9160 to communicate via DTLS. It works, but managing certificates is a bit of a problem. I am using the AT%CMNG command.
First, certificates...
When running example code which involves BLE on nRF52840-based boards, the devices (which have assigned names in the example code) don't show up on the iOS nRF Connect scanner...
Hello,
I am using nRF Connect v2.6.0 and nrf52832 for product development.
I have implemented MCUmgr callbacks to check the DFU status, as shown in the code snippet...
I need to move everything off of UART0 so I can use it for my touchscreen
On a previous post I was told I could move everything to RTT in the overlay, but when I try to...
We've noted that our coordinator sometimes hangs and it's because that sometimes, maybe once every 1000-10000th call, the zb_zdo_mgmt_lqi_req API never responds to the callback...
We have experienced some modem faults and have implemented a custom `nrf_modem_fault_handler` to try to capture them.
We have enabled the config:
CONFIG_NRF_MODEM_LIB_ON_FAULT_APPLICATION_SPECIFIC...
Hi,
I used the reference code from inter_less8_exer3_solution and successfully built it with the nrf5340dk board. However, when building it for the nrf7002dk , I encountered...
I'm using firmware 1.3.6 and sdk 2.7 for Nordic nRF9160. For the internet connection ppp is being used.
Here are the results:
modem shell:
time wget https://leil.de...
Hi,
as i would like to use the uart shell for production purposes as well (e.g. setting the devices serial number) - how can i turn off the shell at runtime (in order to...
Hi,
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
While I've managed...
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
I'm using NCS v2.6.1....
Is it possible for the nRF7002 to operate in both SoftAP and STA modes simultaneously?
From my understanding of the nrfwifi driver, it seems that this functionality may...
