Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi,
I am working with NRF52840, I am using segger embedded studio as V5.42a from that I build the example code as ble_app_proximity. I am getting some error as "Output/Debug...
Hello, I am a private developer of wireless gaming mice in Japan. I am thinking of using Nordic's nRF52840 as the MCU, but can this chip be written to only by USB without...
Hi
I added some code to get the PA/LNA driver enabled in the DFU bootloader on my board accordig to this post:
https://devzone.nordicsemi.com/f/nordic-q-a/50687/pa-lna...
Hello! I am quite new to hardware design with these chips, I have been working with NRF24LUP1 for a while, and have custom bin file for it, not a hex file. and I am unable...
Hi,
I am trying to send the data from SAADC on BLE. I follow the example: https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode...
I use PCA10059 demo board,receive BT data by" nrf connect for desktop",yesterday it is ok,but today when I plug it into my PC,it can't be recognized.and no any indicator,...
My peripheral_demo is already able to work. Now I'm trying to add dfu to it.
I followed the instructions here. (+) Add DFU support to your application - Software - nRF Connect...
I have been able to set up external flash for MCUBoot for FOTA.
But after rebooting, the image is the same than before the image upgrade.
I used a sniffer so i could...
Hi,
I have been looking at the sample https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/simple_at and see that the socket() function uses...
Hi all,
I'm trying something similar to this:
https://devzone.nordicsemi.com/f/nordic-q-a/21628/how-to-use-nrfjprog-dll
i.e. using the nrfprog.dll to connect with a...
Hi,
How do you create a macro in the nRF Connect Mobile app (Android) that displays RSSI in the log every time I receive a temperature signal.
Thanks very much.
Hi,
I have nrf52840 based BMD340 evolution board. I am able to run beacon transmission example.
ble_app_beacon.
Now I want to receive beacons and see the list of it...
I use nrf_fstorage_write() to write data to fstorage. And then I use nrf_fstorage_read() to read data. But data of fstorage written data and reading back are not the same...
Hi,
I have been stuck on this issue for a long time, I have created a buetooth mesh network using NRF52832 IC, which I have completed perfectly.
But the issue is I...
