Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
1. When I start the SEGGER Embed open project: when 10_hello_world_clock_gettime, the following pop-up error pops up: Did not finish 'cmake',
2. When I close the window...
In nRF Connect SDK 1.7.1, how to send hex data over the connection by AT#UDPSEND?
I use AT#XUDPCLI to create UDP client and connect to server.
For the AT#UDPSEND, it seems...
Hi,
1. How do I resolve this error?
2. waring line 93->line 165
3. error : line 104,line114, line128,line 138,
Thank you for all your assistance. Kind regards, Peter...
Hi,
ncs v1.9.1
dk: PCA10090 0.9.0
example :serial_lte_modem
Does this example have the following capabilities?
1. The hex data received from the server in EDRX...
Using the UART example of the 52DK with the TX and RX pins set as 8 and 6 the example works. If I try to change the pins to different pins such as 22 and 23, it does not work...
Hi,nordic
I'm looking for L2CAP Connection Oriented Channels example in NCS,such as Object Transfer Service.
can you tell me some information？
Thanks.
TRANSLATE...
Hi everyone, i would like to put this topic here so that new developers can benefit from it i hope.
when you want to measure the current you need a PPK-2 or Oscilloscope...
Hi expert,
I use the example below:
D:\Nordic\nRF51 SDK\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart
I changed UART pin from default pin0.08 and pin...
My goal is to implement dynamic pairing and connection to a Bluetooth device based on SDK16.0.0 and s132_7.0.1, and add a buttonless DFU function. By sending instructions...
I am trying to integrate GitHub - NordicSemiconductor/IOS-DFU-Library: OTA DFU Library for Mac and iOS, compatible with nRF5x SoCs library in one of the SwiftUI mobile application...
I was starting from multi-NUs.I need to send form a Master a message to 4 Slave every 50mS.
I see that up to 100ms It work but that at 50mS the comunication doesen't work...
Hello,
I was given a project that was built using nRF Connect SDK 1.6.0. I tried installing nRF Connect SDK 1.9.1 but received a bunch of compiler errors when building the...
We upgrade our project from nrf-sdk 1.7.1 to 1.9.1 and it broke part of our project.
The part that broke counts the number of falling / rising edges and triggers different...
Hi team,
I am currently working on a BLE project using nRF5 SDK 17.1.0, I want to interface the nrf52840 DK with the Nrf21540 EK to expand the range.
After reading various...
