Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Dear sirs/madams
I am using SDK 17.0.2
Situation:
One Central unit (nRF52840) and one Peripheral unit (nRF52840) have established a connection (NUS service).
When...
I plan to buy some nRF5340 . I only see 1 chip image from the Nordic Official Website . However, when I clicked on " distributor ", I saw nRF5340 has many different part numbers...
Hi Nordic team,
I am trying to implement DFU over uart in nRF52832 using SDK 17.0.0. My device has nRF52832 and main MCU in it, and I would like to do DFU from main MCU...
Hi
I play with watchdog.
After a watchdog reset the debugger does no longer stop on a breakpoint or generate a hardfault on a __BKPT()
How can I config the Chip to handle...
I have tried nrf_mesh_disable(); but it does not turn off the Provision Beaconing.
mesh_provisionee_prov_listen_stop(); does the trick, however I am struggling with re-enabling...
Hello
when hardfault is happaning, I can catch and understand the reset reason easilly, by looking at the map file
however, from time to time, I get a reset without...
I'm using Segger Embedded Studio version 1.6.0 to try to do some testing with SPI for a future project. Currently I am adding SPI functionality to the "Blinky" example: I...
#define SCAN_INTERVAL 0x00A0 /**< Determines scan interval in units of 0.625 millisecond. */
I am a beginner in this field. I am not sure what does this hexadecimal number...
Hi team:
After my device runs normally for more than 10 hours, the issue that THE socket cannot be created occasionally occurs. Once the issue occurs, the socket cannot...
Hi. I'm working on several projects, some of which are not using Nordic chips. I installed the latest Segger J-Link drivers to support a different project. I believe this...
Hi,
I am using nrf_drv_clock_hfclk_release (); in order to release the hfclk, before the call, the internal counter is 1 and the module is initialized.
because the counter...
I'm working on the NRF Connect SDK v1.6.1 and building the zephyr\samples\net\gsm_modem project, since I'm trying to set up and operate a Nimbelink modem. The code references...
Hi everyone,
I would like to change the output voltage and current driver strength of some GPIO ports on the nRF52840. I am using the zephyr driver "gpio.h" API, but the...
When I try to connect to a previously bonded device, I'm getting
Disconnected (reason 0x3d)
and bt_att: Unhandled ATT code 0x1d
and if I delete the bonds again and try...
I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1.
I am using a function in zboss_api called zb_secur_ic_get_list...
