Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I had a generic USB dongle that I used to receive beacons on my machine from an nRF52832 chip.
To be able to perform OTA DFU, I replaced that generic USB dongle with an...
Dear NORDIC Engineers
I have a qustions about NRF52.We have a project that used NRF52833.We want to add the AOA&AOD function to the project.So I would like to know about...
Building the pc-ble-driver on an Arch Linux machine fails with the following error
./pc-ble-driver/src/pc-ble-driver-4.1.4/src/common/transport/uart_transport.cpp: In member...
Hi,
I'm considering using NRF52832/52840 as BLE central while configuring its I2C as slave.
Should I initialize I2C with TWIS instance? How do I suppose to set the slave...
Hello,
I am using the SMS sample of the NRF9160 SDK version 1.6.1. It allows to automatically send a SMS to a precise phone number, and to receive SMS.
As indicated at...
Hi,
I have been trying to use CMSIS DSP library over nRF52840. I added appropriate CONFIGs in prj.conf file, and cmake file. However, whenever I try to use function from...
Hi,
I would like to change the CDC_ACM UART (CDC_ACM_0) baud rate in runtime mode on nRF5340, but it seems to be not working. Below is my code snippet:
The return value...
Hello,
I am working on project where my requirement is something like... Device will advertise and it gets scanned by its own scanning.
What I have done so far......
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). At that time, an error occurs that "__ICFEDIT_region_RAM_start__" is not defined...
I want to select the nRF52 series SoC as our product platform. I have a use case in which I want to get the optimal channel map and I find the "sd_ble_opt_get()" function...
I have taken over a older (5+ years) project that uses Gazell, but it didn't use the Gazell link layer to do wireless pairing. We were looking at shifting to SDK 12.3 (last...
Hi,
I am using the CAF BLE components to use bluetooth on the nRF52840, which I control over HCI via the nRF9160. This is all working.
To use the CAF advertising component...
Hello Nordic DevZone, My name is Ted, and I'm having some difficulty with a recently installed Nordic / Zephyr SDK and toolchain. On 2021-07-24 I downloaded and installed...
I'm trying to read the memory off of a BT840F, which I'm hoping to do via a debugger. I've read that a tag-connect cable can be used to connect from a pcb to the debug out...
