Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I'm trying to write/read from flash in my app. Reading/writing works until I either:
a) run ant_hrm_rx_start() - then after the call to nrf_fstorage_erase I get "00...
Hello!
I'm from Russia, my name is Anton.
I need a developer kit to research a real-time motion tracking system (RTLS) based on Bluetooth Low Energy, Bluetooth 5.1, Bluetooth...
Привет! Я из России, меня зовут Антон. Мне нужен комплект разработчика для исследования системы отслеживания движения в реальном времени (RTLS) на основе Bluetooth Low Energy...
I am trying to upload an image via BLE DFU, tested on mobile phone and Desktop (Windows) But I receive the following error after all packages have been sent to the device...
Hi,
can nRF52/nRF53 automatically fall back to LDO mode if DCDC enabled in firmware but with bad inductor connection on PCB?
Could re-flash the firmware to disable DCDC...
Hi everyone.
I'm developing a product with nRF5340 and zephyr os. But I found some problems about bluetooth dfu.
Because my application very big. So I can't use defualt...
Hi,
I am evaluating the use of nRF52832/52840 running ZephryOS HCI (Uart or USB) in combination with Bluez/Linux to as central device/gateway. If I were to use the Nordic...
I'm using arm-none-eabi-gcc (10-2020-q4-major or 9-2020-q2-update) to build my firmware. For some reason recently it started to overflow the flash, and I can't figure out...
I inadvertently flashed my PPKII while trying to flash a 52840 Dongle. Now my computer doesn't recognize the PPKII when I plug it into the USB (PPK does not light up). I've...
Just need a little help on something that is probably very simple. I am sure I will be embarrassed at how simple this is.
I get the nr52 device MAC address and append 4...
Hello All,
I have a requirement where temperature Sensor is collecting temperature data constantly. If temperature data is changed by at least 10% from previous value...
Hi Nordic,
I am been using nrf connect sdk 1.5.1 for several days. As far as I can see, there is an example, named nrf desktop in the applications examples.
May I ask...
Hi,
I am trying to interface a BME680 sensor with my nRF5340 DK. I am trying to get the following sample to run (I left everything default): https://developer.nordicsemi...
Hi,
I'm working with the CCS811 sensor example from the `v1.5.1/zephyr/samples/sensor` folder and I managed to compile it successfully after modifying the files in the ...
I am moving my project up to SDK15.2 from SDK14.2 and all is good except when I try to connect a ESP32 device.
When connecting to the 14.2 code, I get this in the debug...
