Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I am moving my project up to SDK15.2 from SDK14.2 and all is good except when I try to connect a ESP32 device.
When connecting to the 14.2 code, I get this in the debug...
Hi Nordic,
I have successfully Implemented a single bank DFU [button less dfu] with my customize service
but I don't know how to enable a dual bank DFU in my services...
Hi! I'm using NRF52832 with SDK 15 and the application is running as expected. To optimize power consumption I'm using a conditional statement to put the chip in sleep mode...
Hi,
I am trying to improve the nrf QSPI driver on Zephyr to handle anomaly 122 on nrf52840. Our application needs access to external flash as also as other modules that...
I'm debugging radio test sample and I'm having some problems. The first step is to compile NRF / samples / peripheral / radio with SES_ Zephyr.hex in test project. Second...
Hello,
I found this great blog entry about synchronizing timers on different devices: https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello, I am using nRF52840, SDK v16.0, mesh SDK 4.2.0 and softdevice S140 7.0.1. I am following this example to experiment PA/LNA features, namely controlling the pins that...
I have a board with the MBN52832 from murata, that i can program with a Jlink with ease, but wont do adv.
I do believe the problem lies with some config that im not doing...
Hi,
I am running the asset tracker v1 app with a few mods, but it seems to reboot once in a while and I cannot find the cause.
The LOG gives nothing away:
[01:07...
I encountered sprintf with the increase of parameters, the power consumption will increase by 2-3uA for each parameter. When I use the sprintf function, the power consumption...
Dear sir,
Good Day!!.
Im using nrf52840 SDv16 and im using Ble_app_uart code, here with i need to add Bluetooth pairing request with password on my android mobile...
Hi,
I try to run the example project "ble_app_hids_keyboard" on a NRF52811 (I use the PCA10040e project, adapted to the NRF52811 on a custom board)
and I always run in...
Hi,
I was reading the values from the FICR of my nrf9160 on my thingy91 and I noticed that when I read the INFO.PART register from the FICR, it returned 0x00009120 rather...
we have BorderRouter- Raspberry pi flashed with nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design .
As an end device I have EFR32 MG12 WSTK flashed with OT-CLI...
I am developing application with buttonles BLE DFU and FreeRTOS. I needed debounce on buttons and decided to use app_button. Here is my init:
I turn on log debug on app_timer...
