I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi,
We are evaluating NRF5340+NRF7002 setup for our customer. We are currently using https client example(sdk v3.0.2). I see that with this example the boot time of the...
I am using the nRF54L15 and NCS SDK v3.0.2 in my project. I need to wake up the board via interrupts from a pressure sensor and a gyro sensor.
The GPIO requirements are...
Hello
I compiled the zephyr example ../zephyr/samples/drivers/i2s/output
The SCK and MCK Signal do have both the same frequency. The bit positioin on MSB in not in the...
I’m implementing static passkey security in a BLE peripheral using nRF52810 with SDK 17.1.0. I have added a feature where the device disconnects automatically if the user...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
Hello,
I am trying to get confirmation regarding if I should expect to receive DeviceShadow events through the nRF Message Routing Service.
https://docs.nordicsemi.com...
Hi.
I made the smallest system module using nRF52840. The schematic diagram is as follows.
My reference design for power supply is as follows,
For Firmware....
I am using nrf5340 audio DK. After plugging it into the computer, 3 VCOMs and RTT will appear. What are these three ports? docs.nordicsemi.com/.../logging_nrf5340.html Here...
I am using nrf5340 audio dk, v3.0.2 SDK. I added CONFIG_BT_TINYCRYPT_ECC=n in prj.conf and got this error: C:/ncs/bumble/hci_uart_0806/prj.conf:23: warning: attempt to assign...
Hello,
You have an outstanding bug related to buffer leak in Bluetooth Mesh suspend-resume operation, NCSDK-31962 https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf...
I want to build the sample usb_hci.
After i create a build config there are warning and the process fails
warning: <choice BT_HCI_BUS_TYPE> (defined at boards/arm/ubx_evknorab10_nrf5340...
Do you give us some software workaround to use SPI (P2.08-MISO, P2.09-MOSI )
The Hardware design refers to datasheet v0.9, connecting P2.08 as MISO and P2.09 as MOSI. From...
Hello,
we are testing the openthread CLI example on nRF54L15dk
We have compiled it with the following options:
CONFIG_OPENTHREAD_CHANNEL_MONITOR =y
CONFIG_OPENTHREAD_CHANNEL_MANAGER...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
