Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
We are doing the certification to our product, in which they asked me to do BLE scan on the 37th channel, then 38th channel and 39th channel separately to pass the certification...
Device: nRF52832
SDK: v15.0.0
SoftDevice: S132 v6.0.0
The SDK v15.0.0 documentation for the peer manager states the following:
Autonomy: The Peer Manager works more...
I'm using SDK 15.3, nRF52840, with the ext-flash read/write QSPI demo project.
block_dev_qspi_init(), in nrf_block_dev_qspi.c, does not uninitialize the QSPI (by calling...
Hi,
I am trying to install nRFgo Studio version 1.21.2 in my Windows 7 (64 bit OS), but half way through, installation is rolling back the installation changes and the installation...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi all,
I use ble_app_blinky example and Android nRF Blinky SDK( https://github.com/NordicSemiconductor...
During developpement of project on nRF52810, we used the nRF52DK PCA10040.
Since we wanted to use P0.9 and P0.10 (to limit differences between eval-board and real board...
I need to develop a ble advertising scanner with these requirements:
- capture at least 10 beacon advertisments (Eddystone TLM) continuously
- advertising interval of...
Hi,
I recently got the nRF51 Dongle for testing of a board with bluetooth interface. I am trying to get this dongle installed in Linux.
I found this link for the SDK...
Hi
I have a project need to be customized advertising frequency and scan in specific frequency
It means nrf52832 could broadcast at specific frequency and scanner also...
Dear Nordic Support,
I am using nRF52840 and BLE SDK v15.2. I want to control my nRF52840 through both UART CLI and BLE CLI so I try and read example: nRF5_SDK_15.2.0_9412b96...
Hello
I have a firmware with Softdevice S132 for NRF52 consists of main application (0x1F000 len:0x56000 ) and Bootloader (0x75000 len:0x9000). What I'm trying to do is...
Dear Nordic Team,
I am using a nRF52832 module purchased from Adafruit ( https://www.adafruit.com/product/3406 ) and I would like to connect it with another device with...
Hi there
First I tell you what I'm, trying to do...
I want to made a connection between a robot and a pc. Over this connection I want to program the robot with new software...
Hi,
I'm using nRF52832 SDK 14.2.0 s132 dfu, softdevice 5.0.0.
And i'm trying to update SD + BL + APP to SDK 15.3.0, softdevice 6.1.1.
When i update pakage by nRF connect...
