My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We need very fast Wi-Fi transfer rates at times. I have been able to tune the code and Wi-Fi driver settings to get up to 30-35 Mbps which is great. But if I don't throttle...
Hi,
Added a function to the coap_client sample code that executes otInstanceFactoryReset by pressing a button and sets it to factory shipping mode. However, it appears that...
I'm developing a system where I want to connect simultaneously to different BLE and ANT+ sensors. I'm using the nRF5340 DK and I would like to be able to select which sensors...
I have a project that I'm pulling in code from multiple_adv_sets using v2.7.0 and sysbuild.
talks about the opcodes and status being in the spec? https://www.bluetooth...
Hello,
We are designing a board with a npm1300 and a nRF5340. A button is connected to npm1300 SHPHLD.
On short-press, we want the npm1300 to send an interrupt to the...
Hi team,
We tested the nRF7002 with the nRF5340 as the host. Now, our application needs to connect the nRF7002 Wi-Fi module with a custom microcontroller other than Nordic...
Hello,
I am trying to establish communication between the nRF9160 SoC and the nRF52840 on the Thingy:91. I have two arrays: one of 774 bytes and another of 8 bytes. Currently...
In the Wi-Fi Fundamentals Course, Lesson 2, Exercise 2 (step 7.2) I found that it is necessary to clear the bssid parameter in the wifi_connect_req_params structure. If it...
Message:
Hi Nordic Semiconductor Dev Zone,
I am developing a PCB that mirrors the one in Sony WF-1000XM5 earbuds, but with the microcontroller replaced by the nRF9161...
I use NRF52832 as a Bluetooth gateway to receive commands and initiate connections to devices. Each instruction received will be interrupted through the IO pin, and the MAC...
OS: Window11
Programmer version : v4.4.0
Used Chip: nRF5340
Used Hex file: peripheral_uart_nrf5340dk.hex
An error occurred while Erase&Write the Hex file while testing...
The default setting for the external flash chip of 9160dk appears to be 64m, but when used, the log display only shows 8m, and only the part within 8m can be used,
Then...
I am trying to send / receive bi-directional audio between two nRF5340 Audio DKs with an external I2S bus on the gateway DK. I am modifying the nrf5340_audio example from...
Hi,
I'm working with nRF5340 and would like to store my own data in the NVM (2 bytes in total).
I couldn't figure out which flash partition is relevant for this and what...
