Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear nordic,
state of your MCUBoot + Immutable bootloader is just awful.
Please fix this hook, when enabled it disables updates of the mcuboot bootloader when used with...
Hi,
From nRF5340 audio example kconfig, there is a note that "now 48kHz is the only sample rate supported". Is this correct? My application would only work for lower bitrate...
Hi,
I have a RIGADO BMD-300 module that can only be accessed over the air. (no physical access)
The modul has the BMDWare ( https://file.elecfans.com/web1/M00/20/D2/oYYBAFmk2JOADMegAAu4fGDEUUo022...
Hello,
I am looking at using the nRF52832 for a safety-related purpose and therefore want to isolate the safety-related code away from the Bluetooth stack. The main concern...
Hi,
I have observed a strange behavior when manually selecting wrong PLMN. I get EMM reject cause 11/PLMN not allowed as expected, but then the modem is stuck in CEREG state...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 Hello. In my project, I want to make sure that my project always works during power on. How can I check if my project can...
I am using a nRF52832 with a LISD3H accelerometer. When I initialize the twi driver, I see a ~250 uA increase in current. I was hoping to initialize the twi driver, enable...
Hello,
I use nRF52832 and SDK 17.02.
I use app_button library to detect and handle button pressing.
Everything works fine except that I have a testcase that is to...
We have a very simple application with an out-of-tree driver that is working fine with NCS 2.0.2.
However, changing to NCS 2.1.0 or 2.1.1 results in a DTS error:
(the...
I am working on a project that uses image differentiaton,person/animal detection, etc. To accomplish this, I can either use OpenCV library or use TinyML lite. The problem...
Hi Nordic:
Maybe it isn't a really question. When I try to make an error check, I get two types of error checks, ERROR_CHECK() and APP_ERROR_CHECK(). It seems to be the...
We would like the Fjorden Grip also to trigger the native iOS camera's shutter button, via sending a “volume up” command—similar to selfie sticks, which however use classic...
I was working and testing protobuf using the zephyr example (nanopb) on 1.9.1 SDK. but in build step fails with this error: ModuleNotFoundError: No module named 'google':...
