We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
first I have to say that I'm new with nRF5340, Segger Embedded Studio and Cmake.
I have a working project with CMakeList.txt. So I include it into Segger Embedded...
Hi.
I am trying communication from nRF52832 to iPhone using ble.
I use main function which put in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart.
But,I...
Hello,
I have done the setup of Lsm5dsl with Nrf52832 DK board but I little bit confused about what hardware configuration is there so please guide me.
This is Code...
Hello Nordic great team,
We have a question please, we would like to configure our IOT device through the air, and the best way as we see in our use case, is to use the...
Hi there,
I tried to configure the openthread co-processor radio.
The build went well for my nRF52840 dongle, I managed to generate the RCP package image but when I install...
Hi!
I'm working with the nRF52833 in a Laird dev kit, the bl653_dvk and I cannot build a Hello World with mcuboot application in nrf sdk 1.7.0 or greater.
Although in...
Added the below lines to the peripheral_hr and I could see the logs without any trouble.
Same lines added to the central_and_peripheral_hr and I can see anything. What I...
Does someone have experience driving several slaves on a QSPI bus? Can we use a general IO pin for Chip Select (CS)? [Edtit] (I believe the nCS - QSPI pin described in the...
Hi,
I am trying to filter an iBeacon sample using a modified version of the central_hr_code.
Changes on the central_hr_code:
Added 128-bit UUID definition:
Added...
Hi,
I am developing a health wearable and want to store biosignal data into flash and then read at some point. I found that the reading process is relative slow as I tested...
Hi,ALL:
I use esb 2.4G liberary,and I found the same kind of produc build of nrf52840,it's radio current consumption is 1.2mA-1.3mA,how can it do it? My project is build...
Hi,
I have 2 nrf52840 DK boards advertising on coded PHY mode. Once connected the connection is updated (using sd_ble_gap_phy_update()) to use 2M mode. No problem in doing...
Hello! I add an attribute array (0x48) for the user cluster. Having problems using the "array" attribute:
1. If you select the data type of 16 or 32 bits, then an alignment...
I have some questions on using the nrfutil dfu ble with the buttonless example.
Should both devices (central and peripheral) be already bonded before starting the DFU process...
Hello,
Using NCS 1.6.1, I would like to use the radio from within a timeslot as suggested in the documentation . However, the MPSL/timeslot sample is quite sparce and only...
