Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I'm considering using NRF52832/52840 as BLE central while configuring its I2C as slave.
Should I initialize I2C with TWIS instance? How do I suppose to set the slave...
Hello,
I am using the SMS sample of the NRF9160 SDK version 1.6.1. It allows to automatically send a SMS to a precise phone number, and to receive SMS.
As indicated at...
Hi,
I have been trying to use CMSIS DSP library over nRF52840. I added appropriate CONFIGs in prj.conf file, and cmake file. However, whenever I try to use function from...
Hi,
I would like to change the CDC_ACM UART (CDC_ACM_0) baud rate in runtime mode on nRF5340, but it seems to be not working. Below is my code snippet:
The return value...
Hello,
I am working on project where my requirement is something like... Device will advertise and it gets scanned by its own scanning.
What I have done so far......
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). At that time, an error occurs that "__ICFEDIT_region_RAM_start__" is not defined...
I want to select the nRF52 series SoC as our product platform. I have a use case in which I want to get the optimal channel map and I find the "sd_ble_opt_get()" function...
I have taken over a older (5+ years) project that uses Gazell, but it didn't use the Gazell link layer to do wireless pairing. We were looking at shifting to SDK 12.3 (last...
Hi,
I am using the CAF BLE components to use bluetooth on the nRF52840, which I control over HCI via the nRF9160. This is all working.
To use the CAF advertising component...
Hello Nordic DevZone, My name is Ted, and I'm having some difficulty with a recently installed Nordic / Zephyr SDK and toolchain. On 2021-07-24 I downloaded and installed...
I'm trying to read the memory off of a BT840F, which I'm hoping to do via a debugger. I've read that a tag-connect cable can be used to connect from a pcb to the debug out...
Hi,
I tried running the "chat" example on two NRF52833DK boards, one as a sender sending a "Hello World" message every 500 milliseconds, the other as a receiver, and found...
Hi,
I have an issue when I migrate my app from nrf52 sdk v16 to v17.
I have setup an app with an uart communication, an app timer and a watchdog. All off these (uart and...
We are using the Libuarte - advanced UARTE driver and sometimes see crashes in the uart_evt_handler code in nrf_libuarte_async.c when it gets a NRF_LIBUARTE_DRV_EVT_RX_DATA...
