Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I'm developing with nRF52811 but firmware is developed for nRF52810.
I think there is no difference between them and that firmware should work well.
But SPIS doesn't work...
THis may have an obvious answer to an experienced embedded programmer but I do not qualify to be that. So I have a piece of working code that runs on the nRF52840 DK and it...
Can you use/link both nfc T4T and T2T libraries and wrapper/driver source in same application/build?
I don't mean emulating both modes at the same time.
Thanks.
To the kind attention of Nordic support team,
I have been using nRF ble sniffer successfully, it is a great tool. But I have some troubles when it comes to use it for ble...
Hi there!
I am placing variables in the ".non_init" section so that their values are retained across software resets. This works great if I only use an App + Soft Device...
I want to modify the uuid through the serial port. What variables can I use to describe this define? Is there any code for reference ?
#define BLE_UUID_NUS_TX_CHARACTERISTIC...
Hi there
I'm currently using three different target platforms/boards #1 : a Nordic PCA10040 - attached to USB #2 : a UTO-NBL-52A developer board - attached to a J-Link plus...
Provisioner and client (provisionee) roles in the same application.
Hello everyone,
First, I am using SDK 17.02 and BLE Mesh 5.0.
By the moment, I want to integrate...
Hello,
I want to realize the data receiving and sending function,so I adapt the transmitter demo in '\nRF5_SDK_16.0.0_98a08e2\examples\peripheral\radio\',and my code is...
Hi all,
we are trying to connect 20 peripherals to one nRF52840 master (connected to a Laptop running a python app with pc-ble-driver-py) and transmit about 1000 Bytes per...
Hi guys,
I have a custom board containing a Raytac nRf52840 module running the Arduino core. The Arduino core configures the nRf52 to expect a 32K crystal on the xtal input...
Hello
I Just got my first Custom PCB's i dont know how to compile the code into them .Can someone help me . I just get the errror messege when i try to find target :
Failed...
Hello, I am using SDK 16.0 and mesh SDK 4.2.
We successfully implemented remote provisioning capabilities in our devices' firmware. One thing we are noticing though is that...
Hi,
I am using spis example from "SDK v17.0.2" with slight modification in the code as given below
On the Master end CS pin is pulled low and send 1 byte(0x45) only...
Hello,
I'm using nrf52840 with gcc compiler and SDK15.3. For our firmware update procedure, we use two flash storage instances. One for the transmitted new application and...
