Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Dear Nordic,
When testing the DFU process, I noticed something unexpected. We are using the secure DFU USB bootloader, with forced dual bank updating. I'll attach both the...
I am using ibeacon format for my device. The specification says to include the RSSI value calibrated at 1 meter in the payload.
Can you please tell me how to find out...
Hi,
We managed to integrate both normal BLE and mesh stack onto our working prototype, powered by nRF52840. So far, it is working well. We are trying to further maximise...
I am using the NRF52840 controller to connect BMD101(ECG sensor) uart based having a baud rate of 57600.
Note: Using UART peripheral example on SDK17
I am trying to parse...
Hi
I've problem on my design when I use voltage translator to communicate with sensors. Can you guys see pictures below:
1.nRF52840 using 3.3v:
1.nRF52840 using...
Hi all.
I want to send my packets in the negotiated time interval.
I sat the NRF_SDH_BLE_GAP_EVENT_LENGTH to 6.
The negotiated TI is 36 ms.
the results are
1- the...
Hello to all,
(If "TLDR" go to "### TLDR ###" in the bottom of the page, where you'll find the straight questions without all the context... ) Me and my team are using the...
Hi,
I noticed that the value raw_uuid_len in function ble_advdata_uuid_find() in module ble_advdata.c is fixed at the value UUID128_SIZE.
So the function can only find...
Hi, I am new to NRF and segger embedded studio.
So I want to send temperature sensor data connected with nrf52840 DK to the Murata1_SC device using UART.
The data will...
Found a potential "weirdness" with the mergehex utilty. When merging hex files containing code, dont seem to have an issue. Recently I was using mergehex create a full programming...
Hello Team,
Can you please confirm if we can use the crypto API to do AES encryption/decryption. Can I use it in non secure app and in application and not in bootloader...
Hi,
We want to make some BLE application for nRF52840 on Thingy:91. Referring to PCA20035 schematic, there are some spare pins which we assume is available for GPIO as...
Hi, we have a product (NRF51 SD8 S110 RBCMesh) on the market that craches about once per year the line that asserts is line 189 in src\\soc_radio_timeslot.c (your code) and...
