We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I am learning to create library in segger. I am using segger example https://wiki.segger.com/How_to_create_a_library_project_and_use_it_in_executable_project
I...
Has anyone managed to get arm-none-eabi-gdb to work with Segger Embedded Studio?
I'm trying to use a Black Magic Probe with SES. I can connect to the nRF dev board with...
Hi,
In our product, I would like to wake up by NFC and than transmit data from the nRF52832 to a PC application over NFC.
My question are:
What NFC type is the most...
I can't seem to find the right configuration item to set to disable the spinning up of the sensor_sim task, which I have no need of in my application.
I've tried setting...
Quick question I think. I'm using the NRF52 to program a PIC16 over SPI. The PIC16 switches it's line to output once it receives a particular command so as such I need to...
Hi,
I'm trying to mimic a fully functional zigbee color light bulb using the nRF52840 dongle.
Starting with the NRF5 Zigbee example light_bulb (examples/zigbee/light_control...
I apologize if this question is stupid
I want to read data in p_adv_report. I use the command NRF_LOG_INFO ("name =% x ", * p_adv_report-> data.p_data); but it's meaningless...
I am trying to use I2C (TWI) to communicate between my custom nRF52811 board with an Arduino. Currently my program hangs at the while (m_xfer_done == false); loop as m_xfer_done...
Hi Team,
We wanted to verify Sleep current numbers for nRF52833 SoC based custom development kit.
Is there any readily available firmware to verify these numbers?
...
I'm teaching a course, using the nRF52840-DK board as the lab platform.
Students download Segger Embedded Studio and compile the "Hello World" project from the 'nRF Samples...
Hi,
I have built a prototype that has two SPI slave devices connected to it and it works perfectly. I have now tried to add an SPI SD card aswell by following the FatFS...
Hi,
I'm now using nRF52833 DK to do the AoA test. I achieved the IQ sampling for a single antenna, but when I tried to switch between multiple antennas, the IQ results seems...
Hello!
My problem is that I am getting duplicates of the ACK packets I send from my PRX device to my PTX device.
To debug this problem, I configured my PTX to continuously...
