Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
I got an error 8(NRF_ERROR_INVALID_STATE) while running ble_nus_c_tx_notif_enble function.
The SDK document shows that, the err_code is
"this API propagates the...
I'm evaluating using zephyr for an nRF52840 based design. I'm able to use the nrfx drivers via Kconfig options. It doesn't appear that there any other Nordic SDK libraries...
Hello developers.
I successfully ran the Mesh project with Light Switch example on nRF52840 devices. And I have 2 questions about this.
Question 1: How can I access from...
Hi.
I'd uesd RTT viewer before SES.
RTT viewer has the menu for saving logs.
I'm a new for SES. I'm recently using SES.
I can see log message on SES, but I don't know...
Hi,
I am just unable to find the FW ID for SD v7.2.0 anywhere.
I am using SDK 17 and s140 7.2.0 and am trying to create a DFU package to update both the Soft Device...
Hello All,
We are testing power consumption nRF52810 in system ON mode , my configurations as below,
Device will advertise for 10 sec connect with the mobile app sends...
I have already went through every step as per what the documentation has stated, but I could not be able to sniff any ZigBee packets using Wireshark. I only want to perform...
I am trying to develop a first eval / test program for the BMD-340-EVAL evaluation board using Keil. However, I don't seem to be able to download the required Keil pack. Other...
Hi,
I want to send multiple packets on a notify characteristic using ble_blanky app as baseline but only first 4 consecutive notifications are received on android side....
I would like to set the UUID below, so please tell me how to set it. 1)base UUID: 2)Service UUID： 3)Status Characteristics UUID： 4)Control Characteristics UUID： 5)Blood...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I set tx power in advertising as below.
sd_ble_gap_tx_power_set...
Hi,
We are developing a product that consists of a "central" and "peripheral" device. A small amount of data is periodically send from the central to peripheral device...
Hi. We are using nRF52832 and we have problem with UARTE. SoftDevice version - S132 5.0.0, SDK version - 14.2.0. Our application uses nRF and Mbed Serial to communicate with...
I have created my own custom project based on the template ble app, porting over the relevant includes and settings in order to start fresh. Despite my section placement file...
Hello,
I'm using a development board PCA10040 with sdk 16.0 I'm trying to organize a data streaming between two devices. Nrf52 board collect data (27 bytes with interval...
