My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hello,
We're making RuuviTag sensor beacons which log environmental data to flash. Logged data is later read by a mobile phone application over Nordic UART Service.
The...
Hello
I am programming using the nrf52832 module 'MDBT42Q-512KV2' in SDK v17.0.
This works well without any problems in the example ble_app_blink. However, the BLE is...
Hello
I am contacting you to have a little more information concerning the messages which are sent in the examples thread_simple_coap_client and thread_simple_coap_server...
We have performed the DTM mode setup on the ATEX HW variant of nRF52832 chipset using nRF go studio application where the app is throwing an error as attached in the screenshot...
This is more related to the Segger Embedded Studio than Nordic parts or SDK, but I'd like to hear what kind of experience other Nordic users are having with the Segger IDE...
I want to run BME680 sensor example from zeyphyr->samples->sensors, i loaded the project with adding nrf9160dk_nrf9160ns overlay file with the contents :
&i2c2 { compatible...
Hi,
we are using the nRF52840 in a medical ECG recorder. To stream the data as fast as possible we want to use the 2Mb phy. Everything is working as expected under iOs and...
Hello,
I am using Nordic's SES 4.52 with a project from nRF Connect SDK 1.3.1. I have preprocessor definitions I'd like to add to the project to mirror those added on the...
The nRF9160 datasheet tells the reader to refer to the website for Altium files. However, the only files I can find are for the development board. Is it possible to release...
What is the best way to change advertising data for each advertising packet in Mesh SDK's each of proxy / dfu / provisioner?
Using Mesh SDK 4.1, it would be ideal to be...
I have a working code which implements a UART peripheral written originally with SDK15.0
I would like to port it to the latest SDK 17.02
I can get advertisement and I...
Hello!
I have problem updating application firmware with the following message.
In nRF Connnect v.3.6.0 Programmer has been selected.
Log file indicated. INFO...
Hi,
We are trying to develop a wearable device that needs to sync time over a BLE connection and write the time to the internal RTC. We are using the nRF52832 for development...
Hi,
I'm experimenting a very high current during advertisement of the nRF52833. When using the "Online Power Profiler", it shows that I should expect peek current of around...
