I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi, I am trying to run ble example - uart in segger embedded studio. I am using 11.0 sdk. I have imported keil project into segger embedded studio. I have the error stating...
Hi devzone,
I'm using translation.
I use nRF52840. I created a firmware like the attached one based on the SDK15.3\examples\peripheral\bie_peripheral\ble_app_blinky. ...
Hi all,
I have a custom board with LED on PIN 11 of nRF52832, and I am using SWD P20 configuration to program my board through nrf52 DK PCA10040. Apparently, nRFgo Studio...
Hi
this is not a question - I'd like to give feedback about the peripheral example usbd_hid_generic.
I'm new to 52840 and new to USB. As learning lesson I tried to build...
Hi All
I am now developing BLE application on nRF52840 DK. I have a question about BLE retransmission process.
When master sends a packet to initiate a connection event...
Hello All,
When I was testing our ble keyboard, there was a problem with the Lenovo tablet connection pairing binding. Please help me, thank you!
1. Ble keyboard is based...
Hi,
I need to send data from a CSV file on the nordic board(Via fatfs library). I have presently gotten a Gatt service up and running.
I have a mobile application which...
Hello ,
Do we need to use TIMER1 ,2etc.. to use TIMER1 ? In my current configuration i have set NRFX_TIMER_ENABLED to 1 and others to 0 "NRFX_TIMER0_ENABLED and other instances...
Hello,
I'm trying to use th nRF52832 as a slave SPI device but in the examples "spis" I see the firmware uses DMA.
Can I use it without DMA?
Also, what is the difference...
Hi ,
I need to generate a count data to third party library.
So I create a timer1 ,it can work well.
But I set time_us equal to 1 ,the "timer_led_event_handler" don...
I am interfacing external RTC PCF8563 to nrf52840. Also I will be using low power sleep mode. Will it be possible to wake up nrf using 1hr alarm interrupt of rtc?
Hi ,
I am working on the project based on nrf9160.
Please verify it-
1. I want to print the current clock source of the board as board is initially work on LFCLK....
Hi!
I am feeling a bit stupid, since I know that I must have made a config error somewhere. I just don't know where. I am developing a BLE HID device using SDK 16.0 and...