Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on System OFF mode.
1...
Hi, i am trying to add additional payload to the Mesh Light Switch example. However, i modified all structs and it came down to the status_handle() function inside generic_onoff_client...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
After wakeup from System OFF (due to GPIO event), I want to validate / debounce...
On the nrfCloud, when you clicked on a device (nrf9160DK), the previous version of the interface would show how much data was used of the "available" data associated with...
We are developing a cycling application and are currently using a variety of ARM processors with BLE capability. We require to add ANT+ capability to read Hear Rate monitor...
Hello,
I'm developping an android application for detecting falls.
I will use accelerometer's values for find the g constant.
But i recover bad values.
this is my...
Without doubt there is a new variation of software emerging:
We are all familiar with Firmware and Software, however I really feel the need to coin the term "Whisper Ware...
I am experiencing a problem where behaviour after an sd_nvic_SystemReset() differs from behaviour after a power-on reset, and this difference causes failures in the softdevice...
Hi, I see there are several questions related to using GPS pulse per second signals for synchronization between devices, but I can't see the responses to some of the questions...
Hi,
I am using Uart1 on nrf52840. This is implemented using nrf_serial library. I have set buffer size to say 10, so event occurs on every 10 bytes reception. Now I want...
Hi,
I have been looking at the Nordic examples and I found them to be pretty slow with the handlers being the bottleneck as opposed to the actual hardware. I was wondering...
I'm developing an application to support multiple concurrent central-and-peripheral connections. It's a bit messy but is just about working. At the moment I'm using SDK 9...
Hello All,
I am facing problem in compiling uECC.c on windows10.
Please any one tell me what is the procedure to build and compile that file.
I have tried on the compiler...
I have a question about the relationship between SDK and sotfDeivce.
I want to use nRF SDK v15.3.0. I know that the document has the following description.
This version...
Hi,
I have no idea why the original libraries are giving me errors such that I didn't change anything from the driver.
Please let me know if I need to do anything in...
