We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
EDIT: Sorry to be posting a lot about my LIS2DH12 problems lately, as I'm advancing somewhat while I have open support threads. Newest thread is here: In preparation of this...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello,
I have an NRF9160DK board and a custom board running the SLM application that are exhibiting similar behaviour. Both boards work fine with the supplied iBasis SIM...
Hello!
I have a custom board with an nRF52805 on it and I am simply trying to run the Zephyr blinky example and verify I can see a GPIO toggling as my first step. I installed...
Hi,
I'm using ble_app_att_mtu_throughput to communicate some data from a nRF52832 to another one. I reached my goal (1.4Mbps) but now I would know what the two board communicate...
Hello, I am going through the Bluetooth Low Energy Fundamentals provided by Nordic.
My nrf 52840 dk could function fine after lesson1, but when I flash my board with the...
Hi,
after upgrading to NCS v2.7.0, I have some trouble with an increased sleep power consumption of our device when I use Zephyr's gpio-keys for the button input.
I was...
Hii,
I am working on DFU OTA using nRF52832 board. I have created rsa-2048 key file (priv.pem) and saved it in my project folder and also, edited CMakeList.txt of project...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
Hi Folks, I’m working with an I2C LCD rated for up to 50KHz and it is showing a fair number of glitches. Can anyone tell me how to lower the I2C speed from the default values...
I am using an NRF52840DK.
1. I erase the chip to start clean:
nrfjprog --eraseall
2. I flash the MCUboot bootloader:
~/mcuboot/boot/zephyr$ west flash
The output...
We have a product based on the nRF52840 which uses the GC9A01 display driven using SPI on battery power. The device also functions as a Bluetooth connectable so it is normally...
Hello DevZone,
I am using a nRF52840 with sdk 17.0.2 with Windows 10
I am trying to setup a connection to my Windows PC but I noticed data fragmentation and a queue...
Hi,
For the SoftDevice controller, how can I send LL_MIN_USED_CHANNELS_IND messages? Is there an API for this, or what scenarios trigger the sending of this message? Thanks...
Hi,
MCU: nrf52840
SDK: nRF5_SDK_17.1.0_ddde560
I am facing such an issue, sometimes after the device's OTA success, and then I would like to upgrade to another version...