Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
i am doing a project where i am modifying secure uart boot loader,
the problem which i am facing is while debugging into boot loader example i am not able to see the...
Hello all,
I've been modifying the thingy:52 mesh demo ( https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo) to support more sensors but I've noticed a severe...
The NRF52810, gives the 0dBm out, with 4.6mA peak current 。
When we using, we plan 20Kpcs for mass product, the current is more 4.6mA， it is 7.4mA 。
we use the 2MBPS air...
I would like to have multiple threads simultaneously accessing the modem via the AT commands over the AF_LTE socket. Thread1 does the normal AT+CFUN=1 and other active commands...
running DFU example from <SDK 15.3>\examples\dfu\secure_dfu_test_images\ble\nrf52840 , and attempting a DFU update of:
sd_s140_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi everyone.
I have a problem with processing with recived UART data. I'm using software UART from example > peripheral > uart.
I use nRF to comunicate with GSM module...
Hello,
how can I store CCCD values in flash?
I read that the peer manager handles it ,but when i reset my device and load all bonded peer data, the CCCDs are not set....
Hello everyone,
i'm trying to hook up an external i2C sensor to P5 connector (TWI_SCL_EXT, TWI_SDA_EXT) and created a device driver template ( from drv_gas_sensor.c example...
What is the max amount of data that can be saved in records in fds?
When we do a dfu, is the data conserved or not?
How to vary the size of the records if possible?
...
Hi all,
Recently, I have concentrated on a mesh project using nrf52840 board programmed sdk_mesh_v_3.1.0. There is a situation that the board needs to send two different...
We have a project to explain the company Shenzhen Zhouhai Technology Co. to invite them as our partner because we see the smart bracelet CK series would be a good option for...
Hello,
We're using the UDP/IP/6LoWPAN layers as provided by the nRF5 SDK 15.0.0.0.
After experiencing sporadic issues in communication we have a question regarding the...
Hi,
I am using BLE_Blinky_Peripheral example from SDK 15.3.0 with s112 softdevice. I want to use basic softdevice APIs instead of nrf_sdh libraries for enabling BLE stack...
