Hi,
i want to build a BLE mesh via advertising. i asked some questions before about ibeacon and observer, how ever to clarify my question i have some additional questions...
Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hello,
Is there any sample code which performs only the most basic functions?
Ie. - Sample code in its simplest form which only sets one pin to an output and sets it...
I'm using SDK 15 and soft device S132 6.0. Using nrf Toolbox to update custom firmware, I'm running into a situation where the DFU update fails with an error code 4 when trying...
Hello,
I have been doing research trying to figure out how to program just the nRF52832 chip. I want to program the nRF52832 chip with the Arduino IDE from sandeepmistry...
Hello!
I am using the nRF2740 board with the nRF8001. If I connect all the pins (SPI, RESET, RDYN, GND) except the Vcc pin I still measure 2.5V at the Vcc pin (Connector...
Hello everyone,
In my current application , I am using nRF52832, with the SDK 11.0. I have a problem with the BLE connectivity, which I think is a hardware issue.
With...
I am doing a connectionless system where I am just broadcasting the data. I am showing a loss of about 50% on the receiver missing the data packets. I have tried before to...
Hello,
I configured pin P1.15 as output and with GPIO_PIN_CNF_DRIVE_H0H1 but I only get 1.7V ?
Does "standard drive" means that the pins can't get to 3V ?
Thank...
My project is based on the Thread cloud coap client example. I would like to know if my CoAP POSTs to the cloud are successful.
I added a "post_response_handler" to the...
Hi,
I've been trying to read/write data from/to the internal flash storage of my nRF52 development board.
I am using SDK11 and softdevice s132
I have modified the flashwrite...
Hi,
I've been trying to read/write data from/to the internal flash storage after a ble disconnect event occurs on my nRF52 development board.
I am using SDK11 and softdevice...
Hello,
i'm developing an interface based on nrf52. The app does a direct connection, performs some exchanges with the peripheral, and tells the peripheral to disconnect...
Hello we have a more stable external reference voltage source than the VBG for the ADC we want to use.
The voltage itself is higher than the allowed reference voltage specified...
Hi,
i am working on a project that in it i had developed a firmware for nrf51844 based on soft device 130 v2.0.1, now i decided to move the project on nrf52840 . i had read...
Hi! I did see a post about this, but is there a way to implement any kind of throttling/flow control over the Nordic UART service?
About the only thing I can imagine is...
Hi,
how can I publish a message to unicast address from a generic on/off client with mesh sdk?
How can I set the address?
Jost to be more precise, the function:...
