Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi,
I'm running a nRF51422QFAC and using sd_temp_get() to read the chip temperature twice / second.
I put it in a temperature chamber and swept the temperature from...
Dear members!
I followed the tutorial of the nRF8001, and tried this code: learn.adafruit.com/.../nrf-uart-in-detail
It worked for me just fine, but...
I have an...
Hi there,
I'm attempting to use the UARTE for a continuous read scenario but I am noticing there is significant delay between the STOPRX task and the ENDRX interrupt (...
Hi,
I'm trying to get a custom PCB working. I can use either the plain peripheral UART, or the ble-app-uart example projects on the NRF52-DK and they work, but they don...
I am using the nRF52 Preview kit (PCA 10036 board) and SDK 0.9.2. Up to this point, I have been able to do everything I want with TWI using the hardware driver. This time...
I tried measuring idle current for nrf51422 board and got something about 1900 uA using multimeter without resistor and with bridge SB9 cut. I know the value is too high....
Dear all:
error occured when I was programming application hex in nRFgo Studio1.20.0,just refer to "program application error.png" ,the error shows "programming failed...
I have a sensor device that needs to transmit every so many seconds. I am looking for a code example to run on nRF52-DK that will do this, sleeping inbetween transmissions...
According to the Gazell using the 1MHz spacing for each channels and the DTM using 2MHz spacing.
Then can we use the DTM channel 0 for Gazell channel 2 to test the Frequency...
I am looking for a nordic BLE development board that can do data transfer through the UART. Something like SPP (Serial Port profile).
Here is what I need;
The iOS and...
Hi,
Question regarding blog from Thomas Søderholm ( blog.nordicsemi.com/.../which-technology-should-i-choose-to-connect-my-wearable-device-to-a-phone):
Can't you do...
Keil 5.18a forces me to install "missing Software Pack"
I am trying to set up SDK 11, SD312, with Keil 5.18a, but when I try to load an example from the SDK 11 examples folder...
Hi! I have a nrf51 that act as a central and a beacon that is my peripheral, they connect to each other using is_uuid_present but I can't enable notification using db_discovery...
Hello,
I am currently designing a PCB containing the nRF51822 chip and I am concerned about how I will be able to update the program.
I have 2 main questions :
I...
Hi,
I developed an application with Nrf51822 with some bonding need.
No problem with android or using the dongle, but using iOs systems it happens that after a random attempt...
