Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I encountered an issue from my custom board who are using a nrf52832.
When i place my board in very cold temperature environment (around -35°C), sometimes the voltage...
Good afternoon,
I am trying to use a function generator to send a sinusoidal function to my nRF7002 DK and I am vizualizing the values in Putty. I am sending with a frequency...
im trying to write drivers of max31341 external rtc, where i been able to successfully able to set time (starting rtc also) in rtc and get time from rtc, so not im trying...
Hi
I'm trying to figure out how to manage my memory on the nrf9160 sip. Currently my application crashes on a specific lines where I try to allocate a large C++ string ...
I'm working with the nrf/samples/net/https_client sample for the nRF9160 and am trying to get a better understanding of using the modem's offloaded TLS capabilities vs. Mbed...
Hello everyone, I am creating a project that uses data received from a GNSS module, however I first wanted to do some tests using a NMEA0183 string and PuTTY. I am trying...
Good morning,
I am trying to understand how the bootloader process works on the nRF5340, and working on the excercises from the intermediate course. The target at the moment...
I cannot re start advertising while connected.
this occurs even when i configure BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED.
I get NRF_ERROR_CONN_COUNT error...
Paring was successful when using nrf_desktop's default device description configs, but after I modified those lines in "prj_keyboard.conf" of keyboard:
CONFIG_DESKTOP_DEVICE_PRODUCT...
Hey there!
I'm playing around with an nRF91 DK using the serial terminal app (the standard one which is programmed during the getting started guide) and am trying to make...
Hi there
So I want to make an application to send mqtt messages over wifi. I have tried to follow the devzone guide: to implement the mqtt api into my software (Mostly the...
While building my first blinky project using nrf connect on VS code it is showing following errors:
C:/ncs/v2.6.1/zephyr/scripts/kconfig/kconfig.py: C:/ncs/v2.6.1/blinky...
Hello,
How can I add serial SRAM or serial Flash to a Thingy:91?
On the nRF9160DK there is 64 Mb external Flash onboard but I assume there is no external Flash on the...
I want to decrypt some packets caught in LE Audio(Using the sample:nRF5340 Audio application), but need the link-key.
According to this case , I add these to prj.conf to...
Hello,
I am using uart with thingy:91 to communicate between nrf52 SoC and nrf91 SiP, i am able to receive data from nrf52 but when i try to send data to nrf52 SoC the function...
