Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi, We are using a Segger JLINK to program a nrf5340 product using the SWD interface. We have been successfully programming units using a design where there is a 100k pullup...
When we try to test the stability of the UARTE peripheral, we find that when inserting and removing the RX pin, the uarte_handler callback function is very likely to goes...
What is the recommended UART SUSPEND sequence to use the PM_DEVICE_RUNTIME? I am having trouble using the PM capabilities with the UARTe driver. I am developing on the 52833...
Hi,
I am trying the https://github.com/NordicDeveloperAcademy/bt-fund blefund_less1_exer1 using nRF52840 DK. I am able to connect but not able to detect button press. I...
SDK:17.1
application: ble_app_uart(+ble_app_buttonless dfu service) bootloader:secure bootloader pca10040e_s112_ble I want to know what operations will be performed when...
Hello,
I saw in an old forum thread ( https://devzone.nordicsemi.com/f/nordic-q-a/79412/lwm2m-amount-of-object-instances-limited ) that block transfer was not fully supported...
Hello! I am using nRF52DK and the nRF Connect SDK with Zephyr to create my custom application. For one part, I am recording IMU values at a frequency of up to 200 Hz and loading...
I am trying to run Gazell libraries on nRF5340. There have been some previous posts about this with answers either saying that the support does not exist, might be coming...
Hello,
I have Micromod nRF52840 module on a carrier board and I've built and flashed Matter Light Switch sample on it but I need to read the logs from the module
How can...
I have a doubt about the BLE callbacks running priority in a thread context. For example, when I define the bt_gatt_notify_func_t callback for the incoming notification, what...
Hi,
I am looking for Bluetooth Broadcaster example program that can run on nRF7002 DK. I am also looking for Bluetooth Observer example program that can run on nRF52840...
The headline says it. I've had this installation about a month and always when I say
nrfutil is taking 100% of CPU. I have up to date ubuntu 22.04 with ubuntu 22.04 in virtualbox...
Currently I'm using nRF52840 and in my application I've defined two GPIOs as an interrupt. one among them is designed such that it changes to output pin, gives a pulse then...
I want to perform ADC high-speed acquisition on IO pins. The solution is SAADC + TIMER + PPI + double buffer. The length of the buffer area is 100. The conversion cycle of...
