Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Dear Sirs:
We use nRF52810 as the key chip in our product, however, we need it to be central or peripheral based on user's option.
So, we would like to apply softdevice...
Hello!
I am currently working on doing the smp_svr sample:
I have done these commands so far (on created from sample application):
west build -b nrf52dk_nrf52832 -d...
Hello DevZone,
I am using Segger embedded studio with multiple build configurations for the two chips and I am having some issues to get the program to compile my nRF52810...
I have tested the sdmmc driver yesterday with both, CS Pin tied directly and via an external i2c port expander. TCA6408A.
Worked like charm, but today I wanted to to some...
We are using nRF9160 chip (in own custom board), SDK 1.9.1 board with "serial lte modem" firmware. We are unable to get coordinates using AGPS. I suppose this is due to the...
Hi!
I am going to use nRF52832 in a new product and wondering whether should I base an application on the new or the old SDK. I have to take into account support for DFU...
Hi,
recently I got Thingy:91 (board info - PCA20035 1.4.0 2020.22),I've updated it to the latest firmware as per instructions. So far so good. Then I started playing around...
I tried to create/ open a project using nRF Connect in SES. The error appears as shown in image. While the file exists as shown in the second image. Why, such error and what...
Hi,
Basically, the setup of the mesh network is as follows,
There are END NODES based on sensor server model.
There are RELAY NODES based on the sensor client model...
Hi,
I am using Zephyr3.0.0 to validate AOA CTE sampling.
Firstly, a s below is the official data format. Nordic Semiconductor Radio peripheral provides 16 bit wide IQ...
Hi,
I am able to successfully build and flash the Matter Light Bulb sample onto my nRF52840 DK.
I am now getting ready to configure the firmware for use on a custom board...
Hi,
NCS1.9.1,nRF5340DK, VSCode，
see code, timer_lms==1000 spend 1000ms
but if start i2s
i2s_audio_init(); //this line will Slow down the time
timer_lms==200 spend...
When i try to use SES to build my project.there is error.The enviroment i confige as descrblied. them i use toochainmanger in nrf connect tools,the error is as the same as...
I'm trying to determine how to get a Linux timestamp for a project using nRF9160. It looks like the mktime() function is not supported. Any suggestions?
thanks!
