Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I use a 52832 as the central device, a 52840 as the peripheral, the two established a connection for a period of time,(After a period of time (approximately 30s), there is...
Hi
I am evaluating nrf9160 with an nrf9160-DK on nb-iot in Greece. I am using the asset tracker application example.
I have an issue of DNS not resolving that is expressed...
I am using NCS v1.7.1. I am developing a custom application on top of 802.15.4, which is based on the 802.15.4 PHY test application.
The problem I am facing can be demonstrated...
Hi here,
I m working with a medical device which should probably have to be certified IEC 61508-SIL 3.
I m still new with that certification process, and wondering if...
Hi all,
I' am sending data from nrf_52840 through zephyr to nrf_connect_app for mobile, iam sending data in decimal format(uint_8t) but iam receiving it in hex,
what can...
Hi
The power profiler app can't find PPK2 after update nrf connect desktop and power profiler.
The programmer and Bluetooth Low Energy app also can't find nrf52dk after...
Hi,
I'm trying to use ble data instead of cli terminal. when nRF52840 received data from ble, I want send the data to cli instance. I called function named "void nrf_cli_print_stream...
Dear Team,
I'm using a custom board to test a radio module based on the nRF52840 chip, in this board the P0.24 pin is tied to a led that blink during the execution of an...
The poly1305 implementation is only covering the obsolete RFC 7539 which got updated by RFC 8439
https://github.com/nrfconnect/sdk-nrfxlib/blob/main/crypto/nrf_oberon/include...
nRF Connect SDK v1.7.1 sample \ncs\v1.7.1\nrf\samples\bluetooth\mesh\light_ctrl\
Long transition times fail due to a 16bit value which needs to be 32bit (I believe, can...
Question regarding nrf5340 ADC input tolerance
If I power the nrf5340 from the VDDH pin at 5V, will the ADC input pins be able to read up to 5V then or just 3.3V?
Thanks...
We have a product that uses the nrf52. Due to availability issues I need to port that project to the nrf51822. Since the nrf51 supports up to sdk 12.3.0 what is the best way...
Hello All,
Thank you in advance for your time and interest in this issue and willingness to provide suggestions.
We have a product that uses the nRF52832 processor in...
Hello,
I'm trying to connect a sensor to the nRF9160 board using the example Asset Tracker v2.
My sensor (SHT30) is connect in I2C to the pins 31 (SCL) and 30 (SDA). In...
