Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi there, I'm trying to build the IOS-nRF-Toolbox, with the hope of using it as the basis of our app. But, I cannot build it with the following errors:
/Users/admin/Documents...
I know there is Current consumption common conditions in the datasheet. (table19. nRF9160_PS_v1.2.pdf)
There is VDD level but It's not described the VDD_GPIO level.
1...
Hi,
I am following the tutorial https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/getting-started-with-nordics-secure-dfu-bootloader...
Hello,
I really find this tutorial useful and substantial. I followed the steps in downloading the github projects but I got the following errors when compiling (Note: I...
Greetings everyone,
I am a beginner in this and would like to ask for help in reading battery level.
Battery info: 3.7V, 100mAh, 0.37wh.
I have tried to read on the...
hai ,
i my application i need to update ota over serial . i m using nrf52840 and sdk 15.2
step 1 : at first flashed uart boot loader code on my board
step 2 : updated...
Hello
I am testing connection between nrf51 dongle and my BLE keyboard using heart_rate_collector sample.but there is an issue with on_service_discovery_response.
my BLE...
Does exist any IC/module of Nordic which could be used as NFC reader/initiator and that has BLE integrated also?
Or just a little BLE module with on-board uFL connector...
Hi Devzone:
We are testing TX and RX range with our customized boards, and encountered a rather bizarre problem:
The connection range is pretty good indoor, maybe 20~30...
I am working on a driver for the Adesto AT25QL641 QSPI Flash Memory chip. Comparing the hardcoded nRF52840 QSPI instruction set and the AT25QL641, they are 90% identical except...
Hi,
I am trying to implement Zigbee mesh and in the Zigbee End device(ZED), I want to know its neighbor table record or routing table record. I did not found any specific...
Hi,
In my application,I have written a code based on ble_hrs sample example. When I am checking the RSSI value at the tablet at 2 meter distance I am getting -56dbm. As...
Hi,
I am planning to design my own custom PCB using the nRF52840 chip.
As I am getting started, I want to make sure all the design rule dimensions are up to the standard...
Hi All,
I am trying to design a BLE module based on the nRF52840 Configuration 6 (Only Battery) provided in the product specification document.
To get started I was using...
